Icom I706MKTMG Quick Split quick split function, Split Lock split lock, SPL Offset split offset

Page 55

SET MODE 7

12QUICK SPLIT (quick split function)

When this item is set to ON, pushing [SPL] for 2 sec. sets the undisplayed VFO frequency to the displayed VFO frequency plus the split offset or duplex offset, and activates split operation.

Quick split function ON

Quick split function OFF.

(default).

 

13SPLIT LOCK (split lock)

When this item is ON the main dial can be used to adjust the transmit frequency (XFC) even while the lock function is activated.

Split lock function OFF

Split lock function ON

(default)

 

14SPL OFFSET (split offset)

This item sets the offset (difference between transmit

 

and receive frequencies) for the quick split function.

Default is 0.100 MHz.

Note that this setting is not valid in FM/WFM modes.

15DUP HF (duplex offset)

This item sets the offset for the duplex function when operating on the HF bands.

Default is 0.100 MHz.

16DUP 50M (duplex offset)

This item sets the offset for the duplex function when operating on the 50 MHz band.

17DUP 144M (duplex offset)

This item sets the offset for the duplex function when operating on the 144 MHz band.

18DUP 430M (duplex offset)

This item sets the offset for the duplex function when operating on the 430 MHz band.

19 1TOUCH RPTR (one touch repeater)

Default is 0.500 MHz.

Default is 0.600 MHz.

Default is 5.000 MHz.

This item sets the offset direction when using the one-touch repeater function. +duplex or –duplex can be selected.

DUP

DUP

Duplex direction is set

Duplex direction is set to

to –duplex.

+duplex.

52

Page 54 Page 56
Image 55
Page 54 Page 56
Contents I706MKG Word Definition Rwarning PrecautionsTable of Contents Front panel Panel Description0MAIN Dial Tension Latch @2PREAMP/ATTENUATOR Switch P.AMP/ATT 2LOCK Switch LockFunction switches Function p VOX Function pSpeech Compressor p BREAK-IN pRear and side panels ACC PIN # Name Description Specifications Color When connecting the ACC conversion cable OPC-599ACC Socket Function display 1DOT Matrix Indicators3FUNCTION Indicators 4DSP IndicatorsHM-103 Schematic Diagram ➊UP/DOWN Switches UP/DN ➋LOCK Switch Lock➌PTT Switch PTT Microphone ConnectorGrounding Installation and ConnectionsPL-259 Connector Installation Example UnpackingFront panel separation InstallationSingle body mounting StandRtty Terminal Required connectionsAdvanced connections Connecting a NON-ICOM Power supply connectionsConnecting the PS-125 / PS-85 DC Power Supply Connecting a NON-ICOM DC Power SupplyExternal antenna tuners and linear amplifier Connecting the AH-4Connecting the AT-180 Connecting the IC-PW1Power on Frequency SettingWhen first applying power CPU resetting Initial settingsExample VFO ModeMemory Mode pgs VFO descriptionBand selection Frequency settingProgrammable tuning steps Hz and 10 Hz tuning stepsSub dial function MHz quick tuning stepTS Switch Flow Chart SSB/CW/RTTY modes Any mode FM/WFM/AM modes➁ Push F-1-F-3 to select a band stacking register Mode selectionOperating Mode Selection Quick band change functionRIT function Receive and TransmitFunctions for receive If shift functionPeak meter hold Noise blankerAGC time constant Preamp and attenuatorSimple band scope RF gain and squelchRF/SQL control priority SSB Filter PresettingOptional filter selection Filter ON/OFFNR Noise Reduction function ANF Automatic Notch Filter functionFunctions for transmit Output power and mic gainDMeter function VOX operation Speech compressorOptional AT-180 Automatic Antenna Tuner operation Manual TuningTuner Operation PTT tune function ➂ The Tuner light lights constantly when tuning is completeOptional AH-4AUTOMATIC Antenna Tuner operation AH-4 operationSplit lock function Split frequency operationQuick split function ➀ Select VFO a and set the frequency to 7.057 MHz/CW➄ Push and hold PTT to transmit release PTT to receive Repeater operation➆ To return to simplex operation, push F-1SPL ➂ Push F-3SCN to toggle tone scan operation on and OFF Tone squelch operationTone scan operation ➅ Communicate in the usual mannerFrequency Duplex Direction One-touch repeater functionAuto repeater function This function automatically activates the repeater setElec KEY Functions for CWConnections for CW CW operationCW pitch control CW reverse modeDElectronic CW keyer Quick SET Mode Setting the electronic keyerConnections for Rtty FSK Functions for RttyConnections for Afsk Rtty FSK operation Presetting for RttyRtty Afsk operation Data socket Adjusting the transmit signal output from the TNCPacket operation Connections for packetSpot measurement Measuring SWRPlot measurement Memory clearing Memory and Scan OperationMemory channels Memory channel selectionProgramming in memory mode Programming in VFO modeMemory/call programming Editing programming memory names Frequency transferringMemory names Calling up memory names➀ Select the S1 display Memo padsWriting frequencies and operating modes into memo pads Calling up a frequency from a memo padPreparation Scan typesPriority watch Programmed scan operationMemory scan operation Select memory scan operationCI-V connection example Remote Jack CI-V InformationData format VFO A=B Command TableGeneral SET ModeQuick set mode operation Initial set mode operationQ4 VOX Gain SSB/AM/FM only Quick set mode itemsQ3 VOX Delay SSB/AM/FM only Q2 MIC Gain SSB/AM/FM onlyQ5 Anti VOX SSB/AM/FM only Initial set mode items RF/SQL SQL/AUTO/RFSQL DUP HF duplex offset Quick Split quick split functionSplit Lock split lock SPL Offset split offsetScan Resume scan resume AM NB Noise blanker in AM modePWR on CHK Power on check Auto Rptr auto repeaterVsend SEL ACC socket output 29 9600 Mode Data socket speedTune Strt auto tuner start PTT Tune PTT tune functionCI-V TRN CI-V transceive LVL Spch S-level speechCI-V Addres CI-V address CI-V Baud CI-V data rateCleaning MaintenanceFuse replacement Memory backupPower Supply Receive Problem Possible Cause Solution TroubleshootingTransmit Display Scan Problem Possible Cause Solution Opening the transceiver case Optional INSTALLATIONS/SETTINGSIf filters DOperation InstallationS2 S1 B a AT-180 internal switch descriptionPIN no Description Name Top view Internal ViewsBottom view Options SP-20EXTERNAL Speaker PS-125DC Power SupplySP-7EXTERNAL Speaker SP-10EXTERNAL Speaker SP-12EXTERNAL SpeakerSpecifications Indication Description No. Indication + power onPower OFF then on to exit initial set mode Menu GuideDisplay Menu SSB/AM/FM mode CW mode Rtty modeMode Display For 2 secCount on us Declaration Conformity About CEEirp Clearance heights by frequency band Installation NotesTypical amateur radio installation Forward clearance, Eirp by frequency bandAbout SP-7 External Speaker Installation Note

I706MKTMG, IC-706MKIIG specifications

The Icom IC-706MKIIG and the Icom IC-706MKTMG are two prominent transceiver models known for their compact design and versatile capabilities. These radios cater to amateur radio enthusiasts, providing a wide range of features suitable for both HF and VHF/UHF operations.

The IC-706MKIIG is a well-regarded dual-band transceiver that operates on HF frequencies from 160 meters to 10 meters and VHF/UHF from 6 meters to 70 centimeters. One of its main features is its compact footprint, making it an excellent choice for mobile operations as well as fixed installation. The transceiver provides up to 100 watts of output power on HF and 50 watts for VHF/UHF, ensuring robust performance for various amateur applications.

On the other hand, the IC-706MKTMG brings the same foundational performance but includes enhanced features aimed at improving user experience. It boasts a high-resolution LCD display with clear visibility under varying light conditions. This model offers advanced digital signal processing (DSP) technology, enhancing audio clarity and reducing noise interference. The built-in auto notch filter and noise blanker efficiently eliminate unwanted signals, allowing users to focus on their desired contacts without distraction.

Both models support multiple modes of operation, including SSB, CW, AM, and FM, which provides versatility in how users can communicate. They feature an easy-to-navigate menu system, allowing users to access settings quickly. With built-in memories and a large number of program settings, operators can customize their experience and quickly switch between configurations.

One standout feature of the IC-706 series is its built-in antenna tuner, which helps match the transceiver to various antenna types, optimizing performance and simplifying setup. The radios also include support for external control via CAT commands, accommodating advanced integration into larger station setups.

In terms of user connectivity, both transceivers come equipped with USB ports and support sound card capabilities, enabling digital modes such as PSK31 and RTTY easily. This integration enhances versatility, catering to modern digital communications alongside traditional voice modes.

Robust, reliable, and feature-rich, the Icom IC-706MKIIG and IC-706MKTMG models stand out as exemplary choices for amateur operators looking for a compact yet comprehensive transceiver solution. Their combination of technologies and characteristics continues to make them popular in the ham radio community.
Top Page Image Contents