Icom IC-706MKIIG, I706MKTMG instruction manual Rear and side panels

Page 8

1 PANEL DESCRIPTION

■Rear and side panels

t y

e r

u i

ANT 1

MIC

w

KEY

!2!3

COMP BEEP GAIN /SIDE T

TUNER

EXT SP

DC 13 . 8V

 

 

q

GND

ANT 2

!1 !0 o

q GROUND TERMINAL [GND] (p. 9)

Connect this terminal to a ground to prevent electri- cal shocks, TVI, BCI and other problems.

w ANTENNA CONNECTORS [ANT 1], [ANT 2] (p. 11) Accept a 50 Ω antenna with an PL-259 type plug.

•[ANT 1] is for connection to an HF/50 MHz antenna.

•[ANT 2] is for connection to 144 MHz antenna.

•These connectors are switched above or below 60 MHz.

When connecting a straight key

When connecting a paddle

(⊕)

(dot)

(com)

(dash)

e DATA JACK [DATA] (p. 12)

6-pin min DIN jack to connect a TNC, etc. for pack- et operation.

r ACCESSORY SOCKET [ACC] (p. 6)

Enables connection to external equipment such as a TNC for data communications, a linear amplifier or an automatic antenna selector/tuner, etc.

•See page at right for socket information.

t RTTY JACK [RTTY] (p. 35)

Connects an external terminal unit for RTTY (FSK) operation.

•The keying polarity and mark/shift frequencies can be selected in quick set mode (p. 48).

y CI-V REMOTE CONTROL JACK [REMOTE]

(p. 45)

Designed for use with a personal computer for remote operation of transceiver functions.

u MICROPHONE CONNECTOR [MIC] (p. 11) Accepts the supplied microphone (connected in par- allel with the front panel’s [MIC] connector).

•See pgs. 1 and 2 for microphone notes.

•See p. 8 for microphone connector information.

iELECTRONIC KEYER JACK [KEY] (p. 33) Accepts a paddle to activate the internal electronic keyer.

• Selection between the internal electronic keyer and

5straight key operation can be made in quick set mode. (p. 49)

o DC POWER SOCKET [DC13.8V] (p. 13)

Accepts 13.8 V DC through the supplied DC power cable.

Rear panel view

!0EXTERNAL SPEAKER JACK [EXT SP] (p. 12) Accepts a 4–16Ω speaker.

!1TUNER CONTROL SOCKET [TUNER] (p. 12) Accepts the control cable from an optional AH-3HF

AUTOMATIC ANTENNA TUNER.

!2SPEECH COMPRESSION LEVEL CONTROL [COMP GAIN] (p. 26)

Adjusts the compression level.

•This control is available only when the speech compres- sor is ON.

Recommended level

Counterclockwise

Clockwise

decreases

increases

COMP

BEEP

GAIN

/SIDE T

Page 7 Page 9
Image 8
Page 7 Page 9
Contents I706MKG Precautions Word Definition RwarningTable of Contents 0MAIN Dial Tension Latch Panel DescriptionFront panel 2LOCK Switch Lock @2PREAMP/ATTENUATOR Switch P.AMP/ATTFunction switches VOX Function p Speech Compressor pBREAK-IN p Function pRear and side panels ACC Socket When connecting the ACC conversion cable OPC-599ACC PIN # Name Description Specifications Color 1DOT Matrix Indicators 3FUNCTION Indicators4DSP Indicators Function display➊UP/DOWN Switches UP/DN ➋LOCK Switch Lock ➌PTT Switch PTTMicrophone Connector HM-103 Schematic DiagramInstallation and Connections PL-259 Connector Installation ExampleUnpacking GroundingInstallation Single body mountingStand Front panel separationRequired connections Rtty TerminalAdvanced connections Power supply connections Connecting the PS-125 / PS-85 DC Power SupplyConnecting a NON-ICOM DC Power Supply Connecting a NON-ICOMConnecting the AH-4 Connecting the AT-180Connecting the IC-PW1 External antenna tuners and linear amplifierFrequency Setting When first applying power CPU resettingInitial settings Power onVFO Mode Memory Mode pgsVFO description ExampleFrequency setting Programmable tuning stepsHz and 10 Hz tuning steps Band selectionMHz quick tuning step TS Switch Flow ChartSSB/CW/RTTY modes Any mode FM/WFM/AM modes Sub dial functionMode selection Operating Mode SelectionQuick band change function ➁ Push F-1-F-3 to select a band stacking registerReceive and Transmit Functions for receiveIf shift function RIT functionNoise blanker AGC time constantPreamp and attenuator Peak meter holdRF/SQL control priority RF gain and squelchSimple band scope Filter Presetting Optional filter selectionFilter ON/OFF SSBANF Automatic Notch Filter function NR Noise Reduction functionDMeter function Output power and mic gainFunctions for transmit Speech compressor VOX operationTuner Operation Manual TuningOptional AT-180 Automatic Antenna Tuner operation ➂ The Tuner light lights constantly when tuning is complete Optional AH-4AUTOMATIC Antenna Tuner operationAH-4 operation PTT tune functionSplit frequency operation Quick split function➀ Select VFO a and set the frequency to 7.057 MHz/CW Split lock function➆ To return to simplex operation, push F-1SPL Repeater operation➄ Push and hold PTT to transmit release PTT to receive Tone squelch operation Tone scan operation➅ Communicate in the usual manner ➂ Push F-3SCN to toggle tone scan operation on and OFFOne-touch repeater function Auto repeater functionThis function automatically activates the repeater set Frequency Duplex DirectionFunctions for CW Connections for CWCW operation Elec KEYCW reverse mode DElectronic CW keyer Quick SET ModeSetting the electronic keyer CW pitch controlConnections for Afsk Functions for RttyConnections for Rtty FSK Rtty Afsk operation Presetting for RttyRtty FSK operation Adjusting the transmit signal output from the TNC Packet operationConnections for packet Data socketPlot measurement Measuring SWRSpot measurement Memory and Scan Operation Memory channelsMemory channel selection Memory clearingMemory/call programming Programming in VFO modeProgramming in memory mode Frequency transferring Memory namesCalling up memory names Editing programming memory namesMemo pads Writing frequencies and operating modes into memo padsCalling up a frequency from a memo pad ➀ Select the S1 displayScan types PreparationProgrammed scan operation Memory scan operationSelect memory scan operation Priority watchData format Remote Jack CI-V InformationCI-V connection example Command Table VFO A=BSET Mode Quick set mode operationInitial set mode operation GeneralQuick set mode items Q3 VOX Delay SSB/AM/FM onlyQ2 MIC Gain SSB/AM/FM only Q4 VOX Gain SSB/AM/FM onlyQ5 Anti VOX SSB/AM/FM only Initial set mode items RF/SQL SQL/AUTO/RFSQL Quick Split quick split function Split Lock split lockSPL Offset split offset DUP HF duplex offsetAM NB Noise blanker in AM mode PWR on CHK Power on checkAuto Rptr auto repeater Scan Resume scan resume29 9600 Mode Data socket speed Tune Strt auto tuner startPTT Tune PTT tune function Vsend SEL ACC socket outputLVL Spch S-level speech CI-V Addres CI-V addressCI-V Baud CI-V data rate CI-V TRN CI-V transceiveMaintenance Fuse replacementMemory backup CleaningTroubleshooting Power Supply Receive Problem Possible Cause SolutionTransmit Display Scan Problem Possible Cause Solution Optional INSTALLATIONS/SETTINGS Opening the transceiver caseIf filters Installation DOperationPIN no Description Name AT-180 internal switch descriptionS2 S1 B a Bottom view Internal ViewsTop view Options PS-125DC Power Supply SP-7EXTERNAL SpeakerSP-10EXTERNAL Speaker SP-12EXTERNAL Speaker SP-20EXTERNAL SpeakerSpecifications + power on Power OFF then on to exit initial set modeMenu Guide Indication Description No. IndicationSSB/AM/FM mode CW mode Rtty mode Mode DisplayFor 2 sec Display MenuCount on us About CE Declaration ConformityInstallation Notes Typical amateur radio installationForward clearance, Eirp by frequency band Eirp Clearance heights by frequency bandInstallation Note About SP-7 External Speaker

I706MKTMG, IC-706MKIIG specifications

The Icom IC-706MKIIG and the Icom IC-706MKTMG are two prominent transceiver models known for their compact design and versatile capabilities. These radios cater to amateur radio enthusiasts, providing a wide range of features suitable for both HF and VHF/UHF operations.

The IC-706MKIIG is a well-regarded dual-band transceiver that operates on HF frequencies from 160 meters to 10 meters and VHF/UHF from 6 meters to 70 centimeters. One of its main features is its compact footprint, making it an excellent choice for mobile operations as well as fixed installation. The transceiver provides up to 100 watts of output power on HF and 50 watts for VHF/UHF, ensuring robust performance for various amateur applications.

On the other hand, the IC-706MKTMG brings the same foundational performance but includes enhanced features aimed at improving user experience. It boasts a high-resolution LCD display with clear visibility under varying light conditions. This model offers advanced digital signal processing (DSP) technology, enhancing audio clarity and reducing noise interference. The built-in auto notch filter and noise blanker efficiently eliminate unwanted signals, allowing users to focus on their desired contacts without distraction.

Both models support multiple modes of operation, including SSB, CW, AM, and FM, which provides versatility in how users can communicate. They feature an easy-to-navigate menu system, allowing users to access settings quickly. With built-in memories and a large number of program settings, operators can customize their experience and quickly switch between configurations.

One standout feature of the IC-706 series is its built-in antenna tuner, which helps match the transceiver to various antenna types, optimizing performance and simplifying setup. The radios also include support for external control via CAT commands, accommodating advanced integration into larger station setups.

In terms of user connectivity, both transceivers come equipped with USB ports and support sound card capabilities, enabling digital modes such as PSK31 and RTTY easily. This integration enhances versatility, catering to modern digital communications alongside traditional voice modes.

Robust, reliable, and feature-rich, the Icom IC-706MKIIG and IC-706MKTMG models stand out as exemplary choices for amateur operators looking for a compact yet comprehensive transceiver solution. Their combination of technologies and characteristics continues to make them popular in the ham radio community.
Top Page Image Contents