Kenmore 153 owner manual Thermostat Removal/Replacement, Element Cleaning/Replacement

Page 19

The water heater should be drained if being shut down during freezing temperatures. Also, periodic draining and cleaning of sediment from the tank may be necessary.

1.Before beginning turn “OFF” the electric power supply to the water heater.

2.CLOSE the cold water inlet valve to the water heater.

3.OPEN a nearby hot water faucet and leave open to allow for draining.

4.Connect a hose to the drain valve and terminate to an adequate drain or outdoors.

5.OPEN the water heater drain valve to allow for tank draining.

NOTE: If the water heater is going to be shut down and drained for an extended period, the drain valve should be left open with hose connected allowing water to terminate to an adequate drain.

6.Close the drain valve.

7.Follow “Filling the Water Heater” instructions in the “Installation Instructions” section.

8.Turn “ON” power to the water heater.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” power.

Thermostat Removal/Replacement

1.Turn “OFF” the electrical power to the water heater at the junction box.

2.Remove the access panel and the insulation cap with handle.

3.Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 29.

4.Disconnect wires from the thermostat.

5.Remove the thermostat from behind the thermostat bracket.

6.Place the new thermostat in the bracket making sure it fits firmly against the tank.

7.Attach the wires to the new thermostat.

NOTE: Some of the terminals may require straight-in wiring through an eye-opening. If wires are now looped, recut and strip wire 3/8” to a straight length and insert.

8.Put plastic terminal cover back in place.

9.Replace the insulation cap with handle to cover the thermostat.

10.Replace access panel, then turn the electric power on.

Element Cleaning/Replacement

NOTE: These instructions are written for element cleaning and element replacement for the lower element. If it is necessary to clean or replace the upper element, then repeat these instructions.

To remove the element from your tank in order to clean or replace it.

19

Image 19
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Misertm Electric Water HeaterSafe INSTALLATION, USE and Service General Safety Table of Contents Introduction Product SpecificationsBasic Tools Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Materials NeededRemoving the Old Water Heater Installation InstructionsInsulation Blankets Facts to Consider About the LocationFacts to Consider About Convertible Lower Element Water Piping Valve and Pipe Insulation Temperature-Pressure Relief ValveFilling the Water Heater Converting the Lower Element Page Wiring Page Wiring Diagrams Upper and Lower Thermostat Adjustments Service and AdjustmentTemperature Regulation Temperature SettingsAnode Rod Inspection Temperature-Pressure Relief Valve OperationDraining Element Cleaning/Replacement Thermostat Removal/ReplacementPage Page Service Drain Valve Washer ReplacementStart Up Conditions TroubleshootingOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Model Numbers Repair Parts ListKenmore Power Misertm Electric Water Heaters Page Page Page MY-HOME
Related manuals
Manual 32 pages 30.3 Kb

153 specifications

The Kenmore 153 is a standout model in the realm of home appliances, particularly noted for its exceptional performance and innovative features. This appliance is designed to meet the demands of modern households, combining efficiency, reliability, and user-friendly features into one compact unit.

One of the primary features of the Kenmore 153 is its robust design, which reflects its commitment to durability. Constructed with high-quality materials, it is engineered to withstand the rigors of daily use while maintaining a sleek and stylish appearance. This model comes with a powerful motor that guarantees efficient operation, enabling users to complete tasks quickly and effectively.

The Kenmore 153 incorporates advanced technology that enhances its functionality. For example, it features smart sensor technology, which automatically detects load size and adjusts water and energy usage accordingly. This not only conserves resources but also ensures optimal cleaning performance with every use. Additionally, the model offers multiple wash cycles and temperature settings, giving users the flexibility to customize their washing experience based on the fabric type and soil level.

Energy efficiency is a significant aspect of the Kenmore 153's design. It boasts an ENERGY STAR certification, indicating that it meets stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency. This not only helps reduce utility bills but also minimizes the environmental impact, making it a wise choice for eco-conscious consumers.

The Kenmore 153 also prioritizes user convenience. Its intuitive control panel allows for easy navigation through various settings and options. A display screen provides clear information about the selected cycle and estimated time remaining, helping users manage their laundry tasks more effectively.

In terms of capacity, the Kenmore 153 is spacious enough to accommodate large loads, making it ideal for families and busy households. Its advanced cleaning system ensures thorough cleaning without damaging clothes, while the high spin speeds reduce drying time significantly.

Overall, the Kenmore 153 stands out for its combination of advanced technology, energy efficiency, and user-centric design. It is a reliable choice for those seeking a powerful and versatile appliance to enhance their laundry experience. Whether you are dealing with everyday clothing or specialized fabrics, the Kenmore 153 promises to deliver exceptional results with every use.