Kenmore 153 owner manual Facts to Consider About the Location, Insulation Blankets

Page 8

Mineral buildup or sediment may have accumulated in the old water heater. This causes the water heater to be much heavier than normal and this residue, if spilled out, could cause staining.

Facts to Consider About the Location

You should carefully choose an indoor location for the new water heater, because the placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not intended for outdoor installation.

Whether replacing an old water heater or putting the water heater in a new location, the following critical points must be observed.

The location selected should be indoors as close to and as centralized with the water piping system as possible. This water heater, as well as all water heaters, will eventually leak. Do not install without adequate drainage provisions so water flow will not cause damage.

WATER HEATERS EVENTUALLY LEAK: Installation of the water heater must be accomplished in such a manner that if the tank or any connections should leak, the flow of water will not cause damage to the structure. When such locations cannot be avoided, a suitable drain pan should be installed under the water heater. Drain pans are available at your local Sears stores. Such drain pans must be piped to an adequate drain.

Water heater life depends upon water quality, water pressure and the environment in which the water heater is installed. Water heaters are sometimes installed in locations where leakage may result in property damage, even with the use of a drain pan piped to a drain. However, unanticipated damage can be reduced or prevented by a leak detector or water shut-off device used in conjunction with a piped drain pan. These devices are available from some plumbing supply wholesalers and retailers, and detect and react to leakage in various ways:

Sensors mounted in the drain pan that trigger an alarm or turn off the incoming water to the water heater when leakage is detected.

Sensors mounted in the drain pan that turn off the water supply to the entire home when water is detected in the drain pan.

Water supply shut-off devices that activate based on the water pressure differential between the cold water and hot water pipes connected to the water heater.

INSTALLATION IN RESIDENTIAL GARAGES: The water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle.

The location selection must provide adequate clearances for servicing and proper operation of the water heater.

Insulation Blankets

Insulation blankets are available to the general public for external use on electric water heaters but are not necessary with this product. The purpose of an insulation blanket is to reduce the standby heat loss encountered with storage tank heaters. Your water heater meets or exceeds the National Appliance Energy Conversation Act standards with respect to insulation and standby loss requirements, making an insulation blanket unnecessary.

Should you choose to apply an insulation blanket to this heater, you should follow these instructions below. Failure to follow these instructions can result in fire, serious personal injury, or death.

Do not cover the temperature and pressure relief (T & P) valve with an insulation blanket.

Do not cover the instruction manual. Keep it on the side of the water heater or nearby for future reference.

Do obtain new warning and instruction labels for placement on the blanket directly over the existing labels.

Facts to Consider About the

Convertible Lower Element

The Upper Element (if a double element model) is a conventional 3800 watt element which only operates at its rated wattage on 240 volts. (See rating plate on the water heater).

The Lower Element of the water heater can be converted from operation at 3800 watts to 5500 watts on a 240 volt system.

Read and follow water heater warnings and instructions. If after reading these instructions in this manual, you do not understand any portion, call Sears Service Center.

Image 8
Contents Power Misertm Electric Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service General Safety Table of Contents Product Specifications IntroductionAdditional Tools Needed When Sweat Soldering Materials and Basic Tools NeededMaterials Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterFacts to Consider About Convertible Lower Element Facts to Consider About the LocationInsulation Blankets Water Piping Temperature-Pressure Relief Valve Valve and Pipe InsulationFilling the Water Heater Converting the Lower Element Page Wiring Page Wiring Diagrams Service and Adjustment Temperature RegulationTemperature Settings Upper and Lower Thermostat AdjustmentsDraining Temperature-Pressure Relief Valve OperationAnode Rod Inspection Thermostat Removal/Replacement Element Cleaning/ReplacementPage Page Drain Valve Washer Replacement ServiceOperational Conditions TroubleshootingStart Up Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Repair Parts List Model NumbersKenmore Power Misertm Electric Water Heaters Page Page Page MY-HOME
Related manuals
Manual 32 pages 30.3 Kb

153 specifications

The Kenmore 153 is a standout model in the realm of home appliances, particularly noted for its exceptional performance and innovative features. This appliance is designed to meet the demands of modern households, combining efficiency, reliability, and user-friendly features into one compact unit.

One of the primary features of the Kenmore 153 is its robust design, which reflects its commitment to durability. Constructed with high-quality materials, it is engineered to withstand the rigors of daily use while maintaining a sleek and stylish appearance. This model comes with a powerful motor that guarantees efficient operation, enabling users to complete tasks quickly and effectively.

The Kenmore 153 incorporates advanced technology that enhances its functionality. For example, it features smart sensor technology, which automatically detects load size and adjusts water and energy usage accordingly. This not only conserves resources but also ensures optimal cleaning performance with every use. Additionally, the model offers multiple wash cycles and temperature settings, giving users the flexibility to customize their washing experience based on the fabric type and soil level.

Energy efficiency is a significant aspect of the Kenmore 153's design. It boasts an ENERGY STAR certification, indicating that it meets stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency. This not only helps reduce utility bills but also minimizes the environmental impact, making it a wise choice for eco-conscious consumers.

The Kenmore 153 also prioritizes user convenience. Its intuitive control panel allows for easy navigation through various settings and options. A display screen provides clear information about the selected cycle and estimated time remaining, helping users manage their laundry tasks more effectively.

In terms of capacity, the Kenmore 153 is spacious enough to accommodate large loads, making it ideal for families and busy households. Its advanced cleaning system ensures thorough cleaning without damaging clothes, while the high spin speeds reduce drying time significantly.

Overall, the Kenmore 153 stands out for its combination of advanced technology, energy efficiency, and user-centric design. It is a reliable choice for those seeking a powerful and versatile appliance to enhance their laundry experience. Whether you are dealing with everyday clothing or specialized fabrics, the Kenmore 153 promises to deliver exceptional results with every use.