Kenmore 153 owner manual AIR in HOT Water Faucets

Page 24

Smelly water may be eliminated or reduced in some water heater

upper and lower thermostats. Follow the instructions to reset the

models by replacing the anode rod (s) with one of less active

high-limit behind the upper and lower access panels.

material, and then chlorinating the water heater tank and all hot

 

water lines. Contact the local Sears Service Center for further

 

information concerning an Anode Replacement Kit #9001453

 

and this Chlorination Treatment. Anode replacement and

 

chlorination of the tank are not covered by the water heater’s

 

limited warranty.

 

If the smelly water persists after the anode replacement and

 

chlorination treatment, then you should consider chlorinating or

 

aerating your water supply.

 

Do not remove the anode leaving the tank unprotected. By

 

doing so, all warranty on the water heater tank is voided.

 

“AIR” IN HOT WATER FAUCETS

 

HYDROGEN GAS: Hydrogen gas can be produced in a hot water system that has not been used for a long period of time (generally two weeks or more). Hydrogen gas is extremely flammable and explosive. To prevent the possibility of injury under these conditions, we recommend the hot water faucet be opened for several minutes at the kitchen sink before any electrical appliances which are connected to the hot water system are used (such as a dishwasher or washing machine). If hydrogen gas is present, there will probably be an unusual sound similar to air escaping through the pipe as the hot water faucet is opened. There must be no smoking or open flame near the faucet at the time it is open.

RUMBLING NOISE

In some water areas, scale or mineral deposits will build up on your heating elements. This buildup will cause a rumbling noise. Follow “Element Cleaning/Replacement” instructions to clean and replace the elements.

HIGH TEMPERATURE SHUT OFF SYSTEM

The water heater has a high limit shut off system with a reset button located on the thermostat.

Follow the resetting instructions which refer to the high limit behind the access panel.

NOTE: If your water heater is connected to an “Off Peak” Clock, and uses the “3 wire lead” wiring diagram in the “Wiring Diagram” section, then the water heater will have a high limit on both the

1.Before beginning, turn “OFF” electrical power supply to the water heater.

FIGURE 44.

2.Remove the two screws securing the access panel and remove panel.

3.Remove the insulation cap with handle.

4.Reset the high limit by pushing in the red button marked “RESET”.

FIGURE 45.

5.Replace the insulation cap with handle so that it completely covers the thermostat and element.

6.Replace the access panel.

7.Turn “ON” electric power to the water heater.

If the high limit must be reset again, call Sears Service Department to find out why the high limit turned “OFF” the electric power.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Power Misertm Electric Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service General Safety Table of Contents Product Specifications IntroductionAdditional Tools Needed When Sweat Soldering Materials and Basic Tools NeededMaterials Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterFacts to Consider About the Location Insulation BlanketsFacts to Consider About Convertible Lower Element Water Piping Temperature-Pressure Relief Valve Valve and Pipe InsulationFilling the Water Heater Converting the Lower Element Page Wiring Page Wiring Diagrams Service and Adjustment Temperature RegulationTemperature Settings Upper and Lower Thermostat AdjustmentsTemperature-Pressure Relief Valve Operation Anode Rod InspectionDraining Thermostat Removal/Replacement Element Cleaning/ReplacementPage Page Drain Valve Washer Replacement ServiceTroubleshooting Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Repair Parts List Model NumbersKenmore Power Misertm Electric Water Heaters Page Page Page MY-HOME
Related manuals
Manual 32 pages 30.3 Kb

153 specifications

The Kenmore 153 is a standout model in the realm of home appliances, particularly noted for its exceptional performance and innovative features. This appliance is designed to meet the demands of modern households, combining efficiency, reliability, and user-friendly features into one compact unit.

One of the primary features of the Kenmore 153 is its robust design, which reflects its commitment to durability. Constructed with high-quality materials, it is engineered to withstand the rigors of daily use while maintaining a sleek and stylish appearance. This model comes with a powerful motor that guarantees efficient operation, enabling users to complete tasks quickly and effectively.

The Kenmore 153 incorporates advanced technology that enhances its functionality. For example, it features smart sensor technology, which automatically detects load size and adjusts water and energy usage accordingly. This not only conserves resources but also ensures optimal cleaning performance with every use. Additionally, the model offers multiple wash cycles and temperature settings, giving users the flexibility to customize their washing experience based on the fabric type and soil level.

Energy efficiency is a significant aspect of the Kenmore 153's design. It boasts an ENERGY STAR certification, indicating that it meets stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency. This not only helps reduce utility bills but also minimizes the environmental impact, making it a wise choice for eco-conscious consumers.

The Kenmore 153 also prioritizes user convenience. Its intuitive control panel allows for easy navigation through various settings and options. A display screen provides clear information about the selected cycle and estimated time remaining, helping users manage their laundry tasks more effectively.

In terms of capacity, the Kenmore 153 is spacious enough to accommodate large loads, making it ideal for families and busy households. Its advanced cleaning system ensures thorough cleaning without damaging clothes, while the high spin speeds reduce drying time significantly.

Overall, the Kenmore 153 stands out for its combination of advanced technology, energy efficiency, and user-centric design. It is a reliable choice for those seeking a powerful and versatile appliance to enhance their laundry experience. Whether you are dealing with everyday clothing or specialized fabrics, the Kenmore 153 promises to deliver exceptional results with every use.
Top Page Image Contents