1.Place the unit in learning mode: With the status light showing solid GREEN, press and hold down both the <SOURCE> and <MUTE> buttons on the front of the soundbar at the same time (approximately 3 seconds) until the status light flashes RED and GREEN.
2.Select the function to learn: Press the <MUTE> button once on the soundbar (the status light changes to solid ORANGE). (Substitute the SOURCE, VOLUME UP & VOLUME DOWN in place of <MUTE> when programming the other buttons during this step)
3.Learn the function: Hold your remote control within one foot and pointed at the front of the soundbar. Slowly press the <MUTE> button on your remote control four times. On the first three presses, the status indicator light will flicker ORANGE with each press. If the unit has successfully learned the function, on the fourth press of the button, the light will flash GREEN several times and then turn to solid GREEN. (Remember to use the VOLUME UP & VOLUME DOWN in place of <MUTE> when programming the other buttons during this step)
To program the remaining functions, simply repeat all steps, substituting <MUTE> with the new function and button presses (VOLUME UP, and VOLUME DOWN) on steps TWO and
THREE.
IMPORTANT NOTE: There is not a power on/off button on the front of the soundbar (there is a “Main Power” switch on the soundbar’s rear panel). You do not need to turn off the soundbar (or subwoofer) when finished watching TV. When finished, turn off your TV (or Satellite or Cable box if the soundbar is connected to that). The soundbar (and the subwoofer) will automatically go into a Standby or “sleep” mode if they do not receive an audio signal from your TV, Satellite or Cable Box for approximately 10 minutes. Standby “On” mode is indicated by a solid red left status light on the soundbar front and on the subwoofer rear panel. When your TV, Satellite or Cable box is turned back on and a signal is again received the soundbar (and subwoofer) will automatically come out of Standby mode and turn on.
Operating the Klipsch icon™ SB 1
Once your soundbar is connected and operating, you will want to complete a few basic steps to get the most enjoyment out of your system. First, you will want to turn off the speakers on your TV and let your soundbar be your new sound source. Some TV’s will automatically turn off their speakers when you connect the soundbar, while others you must manually turn their speakers off. Refer to your TV’s owner’s manual for instructions to turn off the
TV speakers. If you cannot turn your TV speakers off, the soundbar will still give you an excellent enhancement to the sound coming from your TV, and you can easily adjust your TV sound to blend with the soundbar’s sound. To make this adjustment, first program your TV remote to operate the soundbar, then manually turn your TV volume down all the way down from the controls on the TV itself. Next, press the VOLUME UP (+) control on the front of the soundbar until you have a comfortable TV listening volume level coming from the soundbar. Finally, to make sure the Klipsch Icon™ SB 1 subwoofer has a balanced sound with the soundbar, set the subwoofer volume on the subwoofer rear to approximately the halfway point, and then adjust up or down.
ments or specific program material to work properly. To turn on, simply push the “3D” but- ton on the Klipsch Icon™ SB 1 remote and the soundbar will show a white light indicating the feature is on. To turn off, push the 3D button again and the white light will turn off, along with the feature. This effect will work at multiple listening positions in your room. The four control buttons can be programmed into other remote controls using the built-in Learning Remote feature, but the 3D Surround mode On/Off button cannot be learned by any other remote and must be controlled with the included remote.
Troubleshooting
Soundbar does not power on
•Is the power supply plugged into a “live” outlet?
•Is the soundbar “Main Power” rear switch on?
No sound from soundbar
•Is it plugged into a “live” outlet and is the “Main Power” rear switch on?
•Are all connections from TV/Cable or Satellite box pushed in tightly?
•Is TV/Cable or satellite box turned on and the volume turned up?
•Is the soundbar volume turned up?
•Is the soundbar “STANDBY” off? (LED green or orange solid)
•Is the soundbar on the correct source input?
No sound from subwoofer
•Is it plugged into a “live” outlet and “Main Power” rear switch turned on?
•Is the rear subwoofer volume control turned up?
•Has the subwoofer “paired” with the soundbar?
Subwoofer will not wirelessly “pair” with the soundbar (subwoofer green status lights continue flashing)
•Move subwoofer closer to soundbar
•If other wireless devices nearby (i.e. baby monitors. cordless phones, Wi-Fi, etc.) have multiple channel selection, switch their channel
•Turn both the soundbar and subwoofer off, then turn on again to initiate a new pairing sequence
•Using the end of a paper clip (or similar small device) lightly press in button inside of unmarked hole on the left side of input panel to the left of the “L” (red) source input for 5 seconds then, within 10 seconds, lightly press in button, with same device, on back of subwoofer on the top right labeled “Factory Use Only”
