Lochinvar SCH-I-O Flange plate shingle raised #SRM20008, Install flange plate shingle raised

Page 22

SCH Collectors Installation & Operation Manual

3 Roof Attachment Installation

Flange plate shingle (raised) #SRM20008

The raised flange shingle plate is used for inclined installations on asphalt and elastomer roofs; also suitable for flat roofs.

Install flange plate shingle (raised)

1.

Determine roof type. Inspect the structural integrity of

 

the roof and the durability of the roof materials.

2.

Determine the number of collectors needed for the

￿CAUTION

The plates must be screwed into a member capable of bearing the required static load (generally rafters or concrete).

Once installed, the panels must be sealed to the roof sheet material (FIG. 3-28), and only then can the collector be fitted.

 

installation and the number of required attachments

 

from Table 3B or 3C on page 11.

3.

Determine collector connection points (spacing).

 

Measure the spacing of the rafters or trusses to confirm

 

the dimensions and prepare for the system layout

 

(reference the Roof Attachment Spacing Section on

 

page 12).

4.

Caulk (field supplied) around the perimeter of the flange

Unpacking and checking parts

When unpacking the system, check the model names of the components of each system and check to be sure you have the correct number of parts (see FIG. 3-25).

Figure 3-25Kit #SRM20008 - Flange Plate (Raised) Kit Components

FLANGE PLATE RAISED (1X)

SCREW (M10) (4X)

SCREW (M6) (4X)

SQUARE DISK (1X)

HEX NUT (M8) (1X)

HEX BOLT (M8) (1X)

 

plate (FIG. 3-26).

5.

Using the flange plate as a template, place the flange plate

 

on the roof and drill four (4) 6 mm holes as shown in

 

FIG. 3-27. Install the larger screws provided in the kit

 

into the 6mm holes securing the flange plate to the roof

 

(caulk around screws before tightening).

6.

Install the four (4) remaining smaller screws in the

 

perimeter of the flange plate as shown in FIG. 3-27 (caulk

 

around screws before tightening).

7.

Cover the flange plate with roofing material, sealing it to

 

the roof (FIG. 3-28).

Figure 3-26Caulk Around Perimeter of Flange Plate

 

 

CAULK AROUND

 

 

~ Ø 5 mm

 

THE PERIMETER

 

OF THE FLANGE PLATE

 

 

WASHER (M8) (1X)

22

Image 22
Contents Installation & Operation Manual SCH Collectors Contents Introduction Technical dataSCH mounting hardware + hydraulic connection kits How it works SCH CollectorRepresent increased loading additional Dismantling and Disposal Location Array optionsInstallation positions 3SCH Parallel InstallationsHandling and storing What to avoidRoof Attachment Installation Roof attachment typesRoof attachment quantities for SCH collectors snow loading ParallelSpacing Distance 1Spacing DistanceDouble hanger bolt for universal fastening #SRM20001 Installation of roof attachment typesInstall double hanger bolt Unpacking and checking parts4A Install Double Hanger Bolt Components Install rafter anchor Rafter anchor for roof tiles #SRM20003 & #SRM200048Install Rafter Anchor Flat tile hook #SRM20005Install flat tile hook 12Grind Tiles if necessary / Install Hex BoltInstall joint clamp Joint clamp #SRM20006Install cable securing kit Universal cable securing kit #SRM20012Flange plate shingle standard #SRM20007 20 Cable AngleInstall flange plate shingle standard 22Caulk Around Perimeter of Flange PlateInstall flange plate shingle raised Flange plate shingle raised #SRM20008Corrugated metal roof attachment #SRM20013 Unpacking and checking partsInstall metal roof attachment 30Install Rubber SealsInstall wave roof attachment Wave roof attachment #SRM20014 & #SRM20015Install anchor bolt 36Attach Wave Roof Attachment Assembly and Hex Bolt38Pre-Drill 10 mm Hole & Attach to Concrete Collector Installation Horizontal bar lengths2AInstall Horizontal Bars SCH parallel mounting instructionsSide installations 17 Install Plug 20Install Horizontal Bars SCH inclined / non-south facing roof mounting instructions25Lifting Rings Collectors SCH A-frame dimensions Parallel installation Hydraulic connection kits Hydraulic ConnectionsHydraulic expansion kits Connection Expansion SET, Side by SIDE, Parallel Model no Recommended Flow GPM Pressure Drop FT of HD System Start-up Filling, flushing and bleedingClamp ring screw connections Flat seal screw connections Operation, multi-function ball valve and check valveAddress reported problems MaintenanceFluid installation Freezing and boiling points of Aqueous SolutionsSolar circuit Collector Control settingsPump / control function

SCH-I-O specifications

Lochinvar SCH-I-O is a state-of-the-art water heater designed for both residential and commercial applications. This innovative unit is engineered to deliver high efficiency and robust performance while maintaining a compact footprint. One of its standout features is its advanced stainless steel construction, which not only enhances durability but also contributes to the overall efficiency of the heating process.

One of the key technologies utilized in the Lochinvar SCH-I-O is its Smart Control System. This intelligent control feature allows for precise temperature management and ensures optimal operation. The system utilizes a user-friendly digital display that provides real-time information on water temperature, pressure, and operational status. This level of control means less energy consumption and reduced operational costs for users.

The Lochinvar SCH-I-O also incorporates Lochinvar's patented "Copper Heat Exchanger" technology, which maximizes heat transfer while minimizing scale build-up. This innovation not only improves efficiency but also extends the lifespan of the unit. With its low NOx emissions, the SCH-I-O adheres to stringent environmental regulations, making it an eco-friendly option for water heating needs.

Another notable characteristic of this water heater is its configurable design. The SCH-I-O can be easily integrated into existing heating systems or used as a standalone unit, providing versatility for various applications. This means that whether you need it for a single-family home or a larger commercial facility, the SCH-I-O can be tailored to suit your needs.

In addition to its impressive performance metrics, the Lochinvar SCH-I-O is designed with safety in mind. It features multiple safety mechanisms, including high-temperature limit controls and a lock-out function to prevent unsafe operating conditions. These safety features, coupled with its reliable engineering, make the SCH-I-O a trusted choice for many heating professionals and property owners.

The Lochinvar SCH-I-O represents a significant advancement in water heating technology, combining efficiency, advanced control systems, and safety features into one powerful solution. As energy costs continue to rise, investing in such cutting-edge technology not only benefits users' wallets but also promotes sustainable environmental practices. With its robust capabilities, the SCH-I-O stands out as a leading option for dependable hot water heating solutions.