Lochinvar SCH-I-O Corrugated metal roof attachment #SRM20013, Unpacking and checking parts

Page 23

SCH Collectors Installation & Operation Manual

3 Roof Attachment Installation (continued)

Figure 3-27Drill Holes and Attach Flange Plate

COLLECTOR

SUBSTRUCTURE

HEX BOLT

SQUARE DISK

Corrugated metal roof attachment #SRM20013

The corrugated metal roof attachment is used for parallel and inclined mounting on profiled or corrugated sheet metal roofs. The console is mounted above the mounting screws of the profiled or corrugated sheet metal. The two sealing screws are first screwed onto the underlying mounting screw of the sheet. The sealing is done before the console is mounted using the sealing pads supplied. The sections are fixed to the section connectors on the console.

USE THE SMALLER SCREWS IN THE PERIMETER OF THE FLANGE PLATE

PRE-DRILL FOUR (4) 6 MM HOLES - USE THE LARGER SCREWS TO SECURE THE FLANGE PLATE

￿CAUTION

The console must be ordered to fit the relevant profiled or corrugated sheet metal.

The mounting screws supplied with the console must be appropriate in type and length for the particular roof construction.

Figure 3-28Cover Flange Plate with Roofing Material

Unpacking and checking parts

COVER FLANGE PLATE WITH

ROOFING MATERIAL, SEALING

IT TO THE ROOF

2”

6”

4.7” 4.7 mm

> 4.7”

When unpacking the system, check the model names of the components of each system and check to be sure you have the correct number of parts (see FIG. 3-29).

Figure 3-29Kit #SRM20013 - Corrugated Metal Roof Attachment Kit Components

HEX NUT (M10) (1X)

STUD (M10) (1X)

PROFILE CONNECTOR (1X)

8.Slide the square disk onto the hex bolt (see FIG. 3-27).

9.Install the hex bolt with square disk attached into the opening of the flange plate as shown in FIG. 3-27.

Note: Do not tighten hex bolt until ready to install on the collector substructure.

10.Thread the hex nut (M8) and washer (M8) onto the bottom of the hex bolt installed in Step 9.

11.Repeat Steps 4 - 10 until installation is complete.

Install hex bolt onto collector substructure (reference Section 4 - Collector Installation)

HEX BOLT (M8) (1X)

WASHER (M10) (2X)

HEX NUT (M10) (2X)

WASHER (M8) (1X)

23

Image 23
Contents Installation & Operation Manual SCH Collectors Contents SCH mounting hardware + hydraulic connection kits Technical dataIntroduction SCH Collector How it worksRepresent increased loading additional Dismantling and Disposal Array options Location3SCH Parallel Installations Installation positionsWhat to avoid Handling and storingRoof attachment types Roof Attachment InstallationParallel Roof attachment quantities for SCH collectors snow loading1Spacing Distance Spacing DistanceUnpacking and checking parts Installation of roof attachment typesInstall double hanger bolt Double hanger bolt for universal fastening #SRM200014A Install Double Hanger Bolt Components Rafter anchor for roof tiles #SRM20003 & #SRM20004 Install rafter anchorFlat tile hook #SRM20005 8Install Rafter Anchor12Grind Tiles if necessary / Install Hex Bolt Install flat tile hookJoint clamp #SRM20006 Install joint clampUniversal cable securing kit #SRM20012 Install cable securing kit20 Cable Angle Flange plate shingle standard #SRM2000722Caulk Around Perimeter of Flange Plate Install flange plate shingle standardFlange plate shingle raised #SRM20008 Install flange plate shingle raisedUnpacking and checking parts Corrugated metal roof attachment #SRM2001330Install Rubber Seals Install metal roof attachmentWave roof attachment #SRM20014 & #SRM20015 Install wave roof attachment36Attach Wave Roof Attachment Assembly and Hex Bolt Install anchor bolt38Pre-Drill 10 mm Hole & Attach to Concrete Horizontal bar lengths Collector InstallationSCH parallel mounting instructions 2AInstall Horizontal BarsSide installations 17 Install Plug SCH inclined / non-south facing roof mounting instructions 20Install Horizontal Bars25Lifting Rings Collectors SCH A-frame dimensions Parallel installation Hydraulic expansion kits Hydraulic ConnectionsHydraulic connection kits Connection Expansion SET, Side by SIDE, Parallel Model no Recommended Flow GPM Pressure Drop FT of HD Filling, flushing and bleeding System Start-upOperation, multi-function ball valve and check valve Clamp ring screw connections Flat seal screw connectionsFreezing and boiling points of Aqueous Solutions MaintenanceFluid installation Address reported problemsPump / control function Control settingsSolar circuit Collector

SCH-I-O specifications

Lochinvar SCH-I-O is a state-of-the-art water heater designed for both residential and commercial applications. This innovative unit is engineered to deliver high efficiency and robust performance while maintaining a compact footprint. One of its standout features is its advanced stainless steel construction, which not only enhances durability but also contributes to the overall efficiency of the heating process.

One of the key technologies utilized in the Lochinvar SCH-I-O is its Smart Control System. This intelligent control feature allows for precise temperature management and ensures optimal operation. The system utilizes a user-friendly digital display that provides real-time information on water temperature, pressure, and operational status. This level of control means less energy consumption and reduced operational costs for users.

The Lochinvar SCH-I-O also incorporates Lochinvar's patented "Copper Heat Exchanger" technology, which maximizes heat transfer while minimizing scale build-up. This innovation not only improves efficiency but also extends the lifespan of the unit. With its low NOx emissions, the SCH-I-O adheres to stringent environmental regulations, making it an eco-friendly option for water heating needs.

Another notable characteristic of this water heater is its configurable design. The SCH-I-O can be easily integrated into existing heating systems or used as a standalone unit, providing versatility for various applications. This means that whether you need it for a single-family home or a larger commercial facility, the SCH-I-O can be tailored to suit your needs.

In addition to its impressive performance metrics, the Lochinvar SCH-I-O is designed with safety in mind. It features multiple safety mechanisms, including high-temperature limit controls and a lock-out function to prevent unsafe operating conditions. These safety features, coupled with its reliable engineering, make the SCH-I-O a trusted choice for many heating professionals and property owners.

The Lochinvar SCH-I-O represents a significant advancement in water heating technology, combining efficiency, advanced control systems, and safety features into one powerful solution. As energy costs continue to rise, investing in such cutting-edge technology not only benefits users' wallets but also promotes sustainable environmental practices. With its robust capabilities, the SCH-I-O stands out as a leading option for dependable hot water heating solutions.