Therma-Stor Products Group 200 MAX Specifications, Operation, Table of Contents, Location

Table of Contents

Introduction			1
1.	Specifications		2
2.	Operation		2
	2.1	Transporting the Phoenix 200 MAX	2
	2.2	Location	2
	2.3	Electrical Requirements	3
	2.4	Condensate Removal	3
	2.5	Ducting	3
	2.6	Power Switch	3
	2.7	Pump Purge Switch	3
	2.8	Hour Meter	3
	2.9	Defrost Control Adjustment	3
	2.10 Low Pressure Control		4
3.	Maintenance		4
	3.1	Air Filter	4
	3.2	Storage	4
4.	Service		4
	4.1	Warranty	4
	4.2	Technical Description	4
	4.3	Troubleshooting	5
	4.4	Refrigerant Charging	5
	4.5	Blower Replacement	5
	4.6	Compressor/Capacitor Replacement	6
		4.6A Checking Compressor Motor Circuits	6
		4.6B Replacing a Burned Out Compressor	6
		4.6C Replacing a Compressor- Non-Burn Out	7
	4.7	Defrost Thermostat & Timer	7
	4.8	Condensate Pump	7
	4.9	Gravity Drain Option	7
	4.10 Relay		7
5.	Wiring Diagram		8
6.	Service Parts List		9
7.	Warranty		11

Serial No. ___________________________

Purchase Date ______/______/_____

Dealer’s Name ___________________________________

Read the operation and maintenance instructions carefully before using this unit. Proper adherence to these instructions is essential to obtain maximum benefit from your Phoenix 200 MAX dehumidifier.

1 Specifications

Part No.	4024920
Power	110-120 Vac, 7.4 amps; 851 watts
Water	133 pints/day @ AHAM (80°F, 60%)
Removal	240 pints/day @ saturation
	30 gal/day maximum @ saturation
Refrigerant	1 lbs., 14 oz. R-22
Charge
Blower	265 CFM
	Internal Condensate Pump with 20 lift,
	30’ vinyl hose
Operating	33°F to 105°F
Range
Filters	16” x 20”
	Standard	2” Pleated Media 30%* MERV-6
	Optional	2” Pleated Media	30%* MERV-8
	Optional	2” Pleated Media	65%* MERV-11
	Optional	4” Mini-Pleat Media 95%* MERV-14
Duct	Intake – 12” Flex-Duct
Options	Supply – 10” Lay-Flat
Warranty	Five years;
	First year 100% of Parts and Labor
	Second-fifth year 100% of Parts of sealed
	refrigeration system.
Dimensions:
	Cabinet	w/Cart	Shipping
Width	20”	24-1/4”	27-1/2”
Height	40”	40”	45-1/2”
Depth	18-1/4”	21-3/8”	22”
Weight		31 lb	160 lb

2 Operation

2.1 Transporting the Phoenix

The Phoenix 200 MAX must always be upright when transported by vehicle. It may be tipped on to its handle and back for loading and moving by hand.

2.2 Location

Note the following precautions when locating the Phoenix

200 MAX:

•It is designed to be used INDOORS ONLY.

•If used in a wet area, plug it into a GROUND FAULT INTERRUPTER.

•DO NOT use the Phoenix 200 MAX as a bench or table.

•It must always be used in the upright position.

Toll-Free 1-800-533-7533 www.thermastor.com • sales@thermastor.com