Lennox International Inc TUA45S, TUA125S, TUA60S Electrical Connections, Line Voltage Field Wiring

Page 13

6- After it has been determined that each appliance remaining connected to the common venting system properly vents when tested as outlined above, return doors, windows, exhaust fans, fireplace dampers and any other gas-burning appliance to their previous condition of use.

7- If improper venting is observed during any of the above tests, the common venting system must be corrected. The common venting system should be resized to approach the minimum size as determined by using the appropriate tables in Appendix G in the current standards of the National Fuel Gas Code, ANSI Z223-1 in the U.S.A. and the appropriate Category I Natural Gas and Propane appliances venting sizing tables in the current standards of the CSA-B149.1 and .2 in the Natural Gas and Propane Installation Code in Canada.

NOTE - Local codes may supersede any of the above provisions.

Electrical Connections

NOTE - These unit heaters use a direct spark ignition system. There is no pilot necessary as the spark lights the main burner as the gas valve is turned on. The direct spark ignition control board emits radio noise as the sparking process is underway. The level of energy may be sufficient to disturb a logic circuit in a microprocessor controlled thermostat. It is recommended that an isolation relay be used when connecting the unit heaters to a microprocessor controlled thermostat. Install the thermostat according to instructions provided. Select circuit protection and wire size according to the unit rating plate. Install a separate disconnect switch (protected by either fuse or circuit breaker) near the unit so that power can be turned off for servicing. Connect wiring through knockout on the junction box located on the side of the unit heater. Refer to heater wiring diagram for connection information. Use 18 gauge wire or larger for thermostat connections.

Electrically ground unit in accordance with local codes or, in the absence of local codes, in accordance with the current National Electrical Code (ANSI/NFPA No. 70) in the U.S.A., and in Canada with the current Canadian Electrical Code, Part 1 (CSA C22.1).

Make line voltage connections as shown in figure 8. Connect field wiring as shown on wiring diagram on unit. Also refer to typical diagram in this manual. An additional thermostat wire must be run to terminal “G" on heater when continuous blower is desired.

 

LINE VOLTAGE FIELD WIRING

 

UNIT ELECTRICAL BOX

L1

BLACK

N

WHITE

 

 

FIGURE 8

Page 12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents TUA*SN,LA,SF Table Of Contents45, 60, and 75 Unit Dimensions Unit Clearances 125 Unit DimensionsRequirements CSA in the USA ShippingRequirements CSA in Canada Combustion and Ventilation Air Unit Heater InstallationVenting and Combustion Air Inlet Horizontal Venting General Vent and AIR Intake Termination on Single Wall VentHorizontal Venting-Commercial General Condensate Drain Through TEE Pipe and Drain LoopRecommendations Requirements Recommendations and Requirements. In areasCondensate Drain Through Vent Termination Vertical Vent Requirements Horizontal Venting Residential InstallationHorizontal Vent Requirements Horizontal Venting-Residential Two PipesHorizontal Venting Concentric Kit Residential Horizontal Venting Concentric Vent InstallationRemoval Of Unit From Common Vent Electrical Connections Line Voltage Field WiringLeak Check Gas ConnectionGAS Supply to Unit Heater GAS Supply Connection Operation for Honeywell VR8205 Series Gas Valve Figure Unit Start-UpRobertshaw 2000DER GAS Valve White Rodgers 36E GAS ValveTo light the burners manually Attempt to light the burners manuallyHeating Sequence of Operation To Turn Off Gas To UnitIgnition Control LED Optional Gas Conversion KitCombustion Air Inducer Proving Switch Louver Vane AdjustmentFlame Rollout Switch Limit ControlLP/PROPANE GAS Manifold Pressures in.wg. kPa Gas FlowGas Flow Rate Ft.3/Hr Burners Repair PartsFlue Passageway and Flue Box Combustion Air BlowerTUA45/60/75/100/125SN,LA,SF

TUA45S, T-CLASS TM SEPARATED COMBUSTION UNIT HEATERS, TUA75S, TUA100S, TUA60S specifications

Lennox International Inc. stands out as a leader in the heating and cooling industry, and its T-Class™ Separated Combustion Unit Heaters, including models such as TUA60S, TUA100S, TUA125S, and TUA45S, epitomize innovation and efficiency. These unit heaters are engineered to provide reliable warmth in commercial and industrial environments, ensuring comfort and productivity even in the coldest conditions.

One of the most significant features of the T-Class™ heaters is their separated combustion design. This technology allows the heater to draw air for combustion from outside the building, which means that interior air remains untouched and is not used for heating. This design not only improves indoor air quality but also enhances energy efficiency by minimizing heat loss.

The TUA60S, with a heating capacity of 60,000 BTUs, is ideal for smaller spaces, while the TUA100S provides a robust 100,000 BTUs, making it suitable for medium-sized areas. For larger installations, the TUA125S delivers a powerful 125,000 BTUs, ensuring even the most expansive environments remain comfortably warm. Lastly, the TUA45S is perfect for smaller facilities or specific zones requiring efficient heating solutions.

These heaters are equipped with advanced technology such as modulating burners that adjust the heat output based on the current temperature needs, leading to energy savings and reduced operational costs. The T-Class™ units are designed with reliable components, ensuring longevity and reducing maintenance requirements. Additionally, the exterior reflects a modern and durable finish, ensuring they withstand the rigors of industrial settings.

Installation is straightforward thanks to their flexible configurations, allowing for both vertical and horizontal venting options. This adaptability makes them suitable for various applications, from warehouses to manufacturing plants.

In terms of safety, Lennox emphasizes top-tier mechanisms, including built-in safety limits and high-temperature shutoff features to prevent overheating. Furthermore, their models are compliant with industry regulations, reflecting Lennox International's commitment to safety and environmental stewardship.

In conclusion, Lennox International Inc.’s T-Class™ Separated Combustion Unit Heaters, including the TUA60S, TUA100S, TUA125S, and TUA45S, offer a blend of efficiency, reliability, and advanced technology. These heaters are suitable for a variety of commercial and industrial applications, ensuring optimal comfort while prioritizing safety and energy savings.
Top Page Image Contents