Heat & Glo LifeStyle FB-GRAND-S, FB-IN-S owner manual Installation Preparation

Page 10

6 Installation Preparation

Prepare the existing solid fuel masonry or factory built non-combustible firebox for installation.

A. Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open position, OR completely remove it.

E. Fireplace Conversion Notice

Permanently attach the label with the following warning to the inside lower back of the fireplace firebox into which the insert is being installed. Silicone may be required to properly secure the label.

B. Chimney

•Ensure chimney is constructed of non-combustible materials.

•Ensure chimney is clean and in good working order.

•Ensure that all chimney cleanouts fit properly to prevent air leakage into chimney.

C. Gas Line

Note: If the factory built fireplace has no gas access hole provided, an access hole of 1 inch (25 mm) diameter or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship - like manner. This access hole must be plugged with non-combustible insulation after the gas supply line has been installed.

•Install gas line into firebox cavity.

•Check local codes and gas line sizing requirements following NFPA51. See Section 8.

WARNING

Fire Risk.

This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fireplace re- approved by the authority having jurisdiction.

Prior to installing the gas insert:

•Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certi- fied professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

•Replace component parts of the chimney and fireplace as specified by the professionals.

•Ensure all joints are properly engaged and the chimney is properly secured.

D. Hearth or Hearth Extension

WARNING

Fire Risk.

A hearth or hearth extension (if present) must comply with either of the following:

•The solid fuel burning fireplace manufacturer’s specification.

• Local building codes required by authority having jurisdiction.

• NFPA 211

F. Remote Control

The receiver for the remotes must be installed BETWEEN

the base pan of the insert and the firebox of the wood- burning fireplace (see photo below).

EXISTING SIDE

REFRACTORY

REMOTE

RECEIVER

UNIT

EXISTING BOTTOM OF

FIREPLACE

10

Heat & Glo • FB-IN-S, FB-GRAND-S • 783-910 Rev. D • 3/08

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models FB-GRAND-S FB-IN-SCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededLocation Fireplace Size RequirementsMinimum Fireplace Opening Inches MillimetersClearances Clearances to Mantels or other Combustibles above ApplianceFire Risk Asphyxiation Risk Termination LocationsVent Termination Minimum Clearances Foot minimum in snow regionsHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Placing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalGas Pressures Gas InformationFuel Conversions Gas Connection Minimum inlet pressureHigh Altitude Installations Electrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsOptional Accessories Junction Box InstallationInstallation for Fan Optional Shock hazardFAN Junction BOX Finishing Installing Trim SurroundsMantel Projections Accessories Appliance SetupClean the Appliance Ember PlacementLogs Locating Tabs Grate Assembly Heat & Glo FB-IN-S, FB-GRAND-S 783-910 Rev. D 3/08 Positioning the Logs Model FB-IN-SLOG Placement InstructionsFlat Spot for Log #4 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionAfter Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Do not operate appliance with glass door removedFrequently Asked Questions Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaximum flame impingement. Follow lighting instruc Maintaining and Servicing Appliance Maintenance TasksRisk of injury or property damage Inspect Maintenance Tasks Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyPart number list on following Be ordered from an authorized dealer At DepotIncludes Pilot, Pilot Bracket and Air Passge Gaskets FB-IN-S NGKS-FBIN FB-GRAND-S, FB-IN-S StockedLimited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Important operating

FB-GRAND-S, FB-IN-S specifications

The Heat & Glo LifeStyle FB-IN-S and FB-GRAND-S are modern and innovative gas fireplace models that encompass style, comfort, and efficiency. Designed to enhance living spaces, these fireplaces provide both warmth and ambiance, making them a popular choice among homeowners and interior designers alike.

One of the standout features of these fireplaces is their sleek and contemporary design. The FB-IN-S model boasts a minimalist aesthetic that can seamlessly blend with various decor styles, while the FB-GRAND-S offers a more grand presence with its larger viewing area and elegant lines. Both models are constructed with high-quality materials that ensure durability and longevity, providing peace of mind for users.

In terms of technology, both fireplaces are equipped with advanced heating systems that deliver efficient warmth quickly and effectively. The high-performance burner design maximizes heat output while minimizing fuel consumption, resulting in lower energy bills and a reduced carbon footprint. Additionally, these models come with the unique IntelliFire ignition system, which allows for reliable and easy operation. With just the push of a button, users can enjoy instant warmth without the hassle of traditional wood-burning fireplaces.

The LifeStyle series also features customizable flame settings, allowing users to adjust the intensity and height of the flames to create the perfect ambiance for any occasion. The unique flame presentation technology creates a realistic and captivating fire display, enhancing the overall aesthetic of the living space.

Safety is a top priority for Heat & Glo, and both FB-IN-S and FB-GRAND-S models incorporate several safety features. The advanced safety shut-off system ensures that the fireplace operates safely and reliably, while the cool-to-the-touch glass front protects against accidental burns. Additionally, the fireplaces come with options for remote control operation, providing convenience and ease of use.

Another notable characteristic of these models is the wide range of venting options available, allowing for flexible installation in various home layouts. Homeowners can choose from direct vent or top vent configurations, making it easier to integrate the fireplace into any existing space.

In conclusion, the Heat & Glo LifeStyle FB-IN-S and FB-GRAND-S offer a perfect blend of style, technology, and safety. With their modern designs, efficient heating capabilities, customizable flame settings, and advanced safety features, these fireplaces are poised to enhance any home, making them a worthwhile investment for those seeking comfort and elegance in their living spaces.
Top Page Image Contents