Heat & Glo LifeStyle GEM36 manual Vent Termination, Attic Firestop

Page 19

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm).

 

NAILS (4 REQUIRED)

 

RAFTER

CEILING

 

 

CEILING FIRESTOP

Figure 19.

Attic Firestop

C. Vent Termination

For Horizontal Terminations - To attach and secure the termination to the last section of horizontal vent refer to the Cinch Pipe and Termination Cap installation instructions.

•Push and snap-lock the ends as described at the begin- ning of the Installing Vent Components section.

•The termination kit should pass through the wall firestops from the exterior of the building.

•Adjust the termination cap to its final exterior position on the building.

WARNING: THE TERMINATION CAP MUST BE

!POSITIONED SO THAT THE ARROW IS POINT- ING UP.

For trapezoidal cap termination kits:

•Using screws secure the cap to the exterior wall through the flanges in the cap.

!WARNING: VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL OR SID-

ING. VENT TERMINATION CLEARANCES MUST BE FOLLOWED TO AVOID FIRE DANGER. SEE VENT TERMINATION MINIMUM CLEARANCES DI- AGRAM ON THE FOLLOWING PAGE.

7 1/4”

(184mm)

Figure 20. Trapezoid Termination Cap

Heat & Glo • GEM36 • 370-900 Rev. O • 2/05

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents GEM36 Log set assemblyGEM36 Service Parts List / Liste des pièces de rechangeDescription Serial # Part Number Pièce DE Série DE Pièce Intermittent Pilot Ignition Valve AssemblyCertification Installation CodesHigh Altitude Installations Appliance CertificationIntroducing the Heat & Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the GEM36 Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing the Fireplace Framing DimensionsAT Each Joint Tems or Components MAY be Used Installing the Vent SystemMAX .4 M Pilot Shield AdjustmentFlue Restrictor Instructions Vertical VentingVenting with One 90 Elbow + H 1 FTTWO 2 90 o Venting with ONE 1 90 Elbow+ H 1 FT Venting with Three 3 90 ElbowsAttach the First Vent Component to the Starting Collars Installing Vent ComponentsInstall Support Brackets Venting Out the Top Vent12 Hole and Vent Pipe Attic Firestop Vent TerminationPositioned SO That the Arrow is POINT- ING UP Vent Termination Minimum Clearances Leveling and Securing of a Fireplace Positioning, Leveling and Securing the FireplaceIntermittent Pilot Ignition System Vice Must be Wired Directly to the FIRE- Place Junction BOXHeat-Zone Kit Gas Control SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Wiring the Fireplace Finishing Fan Wiring DiagramFacing Thickness from 3/4 to 1-1/4 Facing RequirementsFacing Thickness greater than 1-1/4 GEM42 Ceramic Installing Trim, Logs Ember MaterialClimate Control After the InstallationBefore Lighting the Fireplace Lighting the FireplaceImportant Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance

GEM36 specifications

The Heat & Glo LifeStyle GEM36 is a stunning gas fireplace that harmoniously blends design, functionality, and technology. This contemporary vented fireplace is designed to be the centerpiece of any room, providing warmth while enhancing the aesthetic appeal of spaces ranging from modern living rooms to cozy dens.

One of the standout features of the GEM36 is its impressive viewing area. With a large glass front, this fireplace maximizes visibility, allowing you to enjoy the mesmerizing flames from various angles. The clear, clean lines of the design make it a perfect fit for any décor style, while the customizable options allow homeowners to personalize the look to match their preferences.

The GEM36 incorporates innovative technologies that enhance its performance and user-friendliness. One notable technology is the IntelliFire™ ignition system, which provides reliable and efficient operation. This system offers the convenience of remote control, making it easy to ignite the fire from a distance, ensuring a warm welcome every time you walk into the room.

In terms of efficiency, the GEM36 boasts an impressive heat output, ensuring spaces are not only stylish but also comfortable year-round. The adjustable flame height provides control over the ambiance, allowing users to create the perfect setting for any occasion. This efficiency is complemented by the advanced combustion technology designed to ensure cleaner burning and improved heat management.

Moreover, the LifeStyle GEM36 offers various decorative media options to suit individual tastes. Homeowners can choose from traditional log sets to modern glass or stone accents, allowing for a customized look that enhances the overall aesthetic of the fireplace.

Safety is also a priority with the GEM36, which incorporates features designed to minimize risk. The fireplace is equipped with safety sensors that monitor gas levels and ensure safe operation, providing peace of mind for users.

In summary, the Heat & Glo LifeStyle GEM36 is more than just a fireplace; it is a statement piece that combines elegance, innovation, and safety. With its impressive features, including IntelliFire™ ignition, customizable aesthetics, and high-efficiency performance, the GEM36 is an excellent choice for those looking to elevate their living spaces and enjoy the warmth and comfort of a gas fireplace.
Top Page Image Contents