Heat & Glo LifeStyle GEM36 manual Gas Supply Line, Gas Pressure Requirements

Page 23

Step 7. The Gas Supply Line

NOTE: Have the gas supply line installed in accordance with local building codes by a qualified installer ap- proved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

NOTE: Before the first firing of the fireplace, the gas supply line should be purged of any trapped air.

NOTE: Consult local building codes to properly size the gas supply line leading to the 1/2 inch (13mm) hook-up at the unit.

This gas fireplace is designed to accept a 1/2 inch

(13 mm) gas supply line. To install the gas supply line:

•A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13mm) tee-handle manual shut-off valve and a listed flexible gas connector are connected to the 1/2 inch (13mm) inlet of the control valve. NOTE: If substi- tuting for these components, please consult local codes for compliance.

•Locate the gas line access hole in the outer casing of the fireplace.

•The gas line may be run from either side of the fireplace provided the hole in the outer wrap does not exceed 2 1/2” in diameter and it does not penetrate the actual firebox.

•The gap between the supply piping and gas access hole can be plugged with non-combustible insulation to pre- vent cold air infiltration.

•Open the fireplace lower grille, insert the gas supply line through the gas line hole, and connect it to the shut-off valve.

•When attaching the pipe, support the control so that the lines are not bent or torn.

•After the gas line installation is complete, all connec- tions must be tightened and checked for leaks with a commercially-available, non-corrosive leak check solu- tion. Be sure to rinse off all leak check solution following testing.

!WARNING: DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

•At the gas line access hole, use insulation to re-pack the space around the gas pipe.

•Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing.

Step 8. Gas Pressure Requirements

Pressure requirements for Heat & Glo gas fireplaces are shown in the table below.

Pressure

Natural Gas

Propane

Minimum

5.0 inches

11.0 inches

Inlet Pressure

w.c.

w.c.

Maximum Inlet

14.0 inches

14.0 inches

Gas Pressure

w.c.

w.c.

Manifold

3.5 inches

10.0 inches

Pressure

w.c.

w.c.

 

 

 

A one-eighth (1/8) inch (3 mm) N.P.T. plugged tapping is provided on the inlet and outlet side of the gas control for a test gauge connection to measure the manifold pressure. Use a small flat blade screwdriver to crack open the screw in the center of the tap. Position a rubber hose over the tap to obtain the pressure reading.

The fireplace and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of one-half (1/2) psig (3.5 kPa).

The fireplace must be isolated from the gas supply piping system by closing its individual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than one-half (1/2) psig (3.5 kPa).

Heat & Glo • GEM36 • 370-900 Rev. O • 2/05

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents GEM36 Log set assemblyGEM36 Service Parts List / Liste des pièces de rechangeDescription Serial # Part Number Pièce DE Série DE Pièce Intermittent Pilot Ignition Valve AssemblyCertification Installation CodesHigh Altitude Installations Appliance CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Fireplaces Diagram of the GEM36 Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Framing the Fireplace Framing DimensionsAT Each Joint Tems or Components MAY be Used Installing the Vent SystemMAX .4 M Pilot Shield AdjustmentFlue Restrictor Instructions Vertical VentingVenting with One 90 Elbow + H 1 FTTWO 2 90 o Venting with ONE 1 90 Elbow+ H 1 FT Venting with Three 3 90 ElbowsAttach the First Vent Component to the Starting Collars Installing Vent ComponentsInstall Support Brackets Venting Out the Top Vent12 Hole and Vent Pipe Positioned SO That the Arrow is POINT- ING UP Vent TerminationAttic Firestop Vent Termination Minimum Clearances Leveling and Securing of a Fireplace Positioning, Leveling and Securing the FireplaceIntermittent Pilot Ignition System Vice Must be Wired Directly to the FIRE- Place Junction BOXHeat-Zone Kit Gas Control SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Wiring the Fireplace Finishing Fan Wiring DiagramFacing Thickness greater than 1-1/4 Facing RequirementsFacing Thickness from 3/4 to 1-1/4 GEM42 Ceramic Installing Trim, Logs Ember MaterialClimate Control After the InstallationBefore Lighting the Fireplace Lighting the FireplaceImportant Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance

GEM36 specifications

The Heat & Glo LifeStyle GEM36 is a stunning gas fireplace that harmoniously blends design, functionality, and technology. This contemporary vented fireplace is designed to be the centerpiece of any room, providing warmth while enhancing the aesthetic appeal of spaces ranging from modern living rooms to cozy dens.

One of the standout features of the GEM36 is its impressive viewing area. With a large glass front, this fireplace maximizes visibility, allowing you to enjoy the mesmerizing flames from various angles. The clear, clean lines of the design make it a perfect fit for any décor style, while the customizable options allow homeowners to personalize the look to match their preferences.

The GEM36 incorporates innovative technologies that enhance its performance and user-friendliness. One notable technology is the IntelliFire™ ignition system, which provides reliable and efficient operation. This system offers the convenience of remote control, making it easy to ignite the fire from a distance, ensuring a warm welcome every time you walk into the room.

In terms of efficiency, the GEM36 boasts an impressive heat output, ensuring spaces are not only stylish but also comfortable year-round. The adjustable flame height provides control over the ambiance, allowing users to create the perfect setting for any occasion. This efficiency is complemented by the advanced combustion technology designed to ensure cleaner burning and improved heat management.

Moreover, the LifeStyle GEM36 offers various decorative media options to suit individual tastes. Homeowners can choose from traditional log sets to modern glass or stone accents, allowing for a customized look that enhances the overall aesthetic of the fireplace.

Safety is also a priority with the GEM36, which incorporates features designed to minimize risk. The fireplace is equipped with safety sensors that monitor gas levels and ensure safe operation, providing peace of mind for users.

In summary, the Heat & Glo LifeStyle GEM36 is more than just a fireplace; it is a statement piece that combines elegance, innovation, and safety. With its impressive features, including IntelliFire™ ignition, customizable aesthetics, and high-efficiency performance, the GEM36 is an excellent choice for those looking to elevate their living spaces and enjoy the warmth and comfort of a gas fireplace.
Top Page Image Contents