Heat & Glo LifeStyle 6000TR-OAK-IPI Before Lighting the Fireplace, Air Shutter Setting

Page 34

This statement is in compliance with SPCS 16 CFR Sec- tion 1201.5 “Certification and labeling requirements” which refers to 15 USC 2063 stating “…Such certificate shall ac- company the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please con- tact your dealer or distributor to order.

Step 12. Before Lighting the Fireplace

Before lighting the fireplace, be sure to do the following:

Remove all paperwork from underneath the fireplace. Review safety warnings and cautions

•Read the Safety and Warning Information section at the beginning of this Installers Guide.

Double-check for gas leaks

•Before lighting the fireplace, double-check the unit for possible gas leaks.

Double-check vent terminations and front grilles for obstructions.

•Before lighting the fireplace, double-check the unit for possible obstructions that could be blocking the vent ter- minations or the front grilles.

Double-check for faulty components

•Any component that is found to be faulty MUST BE re- placed with an approved component. Tampering with the fireplace components is DANGEROUS and voids all war- ranties.

A small amount of air will be in the gas supply lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and will operate normally.

Subsequent lightings of the fireplace will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

NOTE: The fireplace should be run 3 to 4 hours on the initial start-up. Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the fireplace for an additional 8 hours. This will help to cure the products used in the paint and logs.

During this break-in period it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the fireplace’s initial burning.

Air Shutter Setting

This fireplace has an adjustable air shutter (which controls the primary air) factory set for the minimum vertical vent run (see Figure 43). If your installation has more than the minimum required vertical vent length, adjustment of the air shutter may be necessary to obtain optimal flame appearance. This should be adjusted by a qualified installer at the time of installation.

By pushing the air shutter handle in, you will be closing the air shutter. To adjust loosen the wing nut. Care should be taken when adjusting the air shutter so as not to cause the fireplace to soot. If sooting occurs the air shutter will need to be opened by pulling the handle out. When finished tighten wing nut.

AIR SHUTTER

WING NUT

Figure 43.

34

Heat & Glo • 6000TR-OAK, 6000TR-OAK-IPI • 383-901 Rev. K • 5/06

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Installation and Operation What to do if you smell gasSafety and Warning Information Table of Contents Log Set Assembly 6000TR-OAK-IPIService Parts List 6000TR-OAK, 6000TR-OAK-IPI LOGS-6OAKValve Assembly Intermittent Pilot IgnitionStanding Pilot Ignition Valve Assembly 6000TR-OAKAppliance Certification Installation CodesHigh Altitude Installations CertificationVent Directly BELOW. Keep Clear of ALL OB- Structions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Introducing the Heat & Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000TR-OAK, 6000TR-OAK-IPI Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing Dimensions Framing the FireplaceDVP90ST Tems or Components MAY be Used Installing the Vent SystemVent System Approvals Identifying Vent ComponentsVertical Venting Flue Restrictor InstructionsMAX .4 M Straight Up Vertical Venting Chart Venting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with TWO 2 90 o Elbows Venting with Two 90 ElbowsVenting with Three 3 90 Elbows Venting with three 90 elbows+ V 1 FT + H 1 FT Installing Vent Components Continue Adding Vent Components To Install the Heat ShieldInstall Support Brackets Above the First 900 Elbow in the Venting System12 Hole and Vent Pipe Attic Firestop Vent TerminationHorizontal Termination Minimum Clearances for Terminations Positioning, Leveling, and Securing the Fireplace Proper Positioning Leveling and Securing of a FireplaceGas Control Systems Step Installing the Optional Heat-Zone-Gas KitVice Must be Wired Directly to the FIRE- Place Junction BOX Standing Pilot Ignition SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Optional Accessories Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Wall SwitchOperation using Battery Power BRNFinishing Sealant Material Hearth ExtensionsInstalling Trim, Logs, and Ember Material 6000TR-OAK Tempered 6000TR-OAK-IPI TemperedAir Shutter Setting Double-check for faulty componentsBefore Lighting the Fireplace Lighting the Fireplace After the InstallationFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace

6000TR-OAK-IPI specifications

The Heat & Glo LifeStyle 6000TR-OAK-IPI is a modern gas fireplace designed to enhance the ambiance of any living space while providing efficiency and convenience. This model stands out for its innovative features and sleek design, making it a popular choice for homeowners looking to combine aesthetics with functionality.

One of the main features of the LifeStyle 6000TR-OAK-IPI is its realistic oak log set, which provides a traditional fireplace look without the hassle of wood. The logs are accentuated by a vibrant flame that can be adjusted to suit the user's preferences, ensuring a cozy atmosphere whether for a small gathering or a romantic evening.

The fireplace incorporates advanced technology, notably the Intellifire Ignition System (IPI). This system not only simplifies the ignition process but also enhances safety and energy efficiency. The IPI technology ensures that the fireplace ignites smoothly whenever needed and automatically shuts down when not in use, conserving gas and reducing costs.

Another significant characteristic of the LifeStyle 6000TR is its customizable design. Homeowners can choose from various trim and surround options, allowing the unit to blend seamlessly with different interior styles. The fireplace features a large viewing area, delivering a mesmerizing spectacle of flames that draws the eye and serves as a stunning focal point in any room.

Performance-wise, the LifeStyle 6000TR boasts an impressive heating capacity. With its powerful heat output, it can effectively warm a large area, making it perfect for open-concept living spaces. Furthermore, its efficient combustion system ensures that emissions are minimized, making it an environmentally friendly option.

Installation is made easier with the model's flexible venting options, allowing for both direct venting and vent-free configurations. Homeowners can select the installation method that best suits their heating needs and home design.

With a combination of style, efficiency, and modern technology, the Heat & Glo LifeStyle 6000TR-OAK-IPI is an exceptional choice for those looking to elevate their home heating experience. It blends warmth with aesthetic appeal, making it a worthwhile investment for any household.
Top Page Image Contents