Heat & Glo LifeStyle 6000TR manual Getting Started, If YOU are Using the Rear SET of Vent Collars

Page 5

Introducing the

Heat-N-Glo

Gas Fireplaces

Pre-install Preparation

Heat-N-Glo direct vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems.

Gas fireplace diagrams, including the dimensions, are shown in this section.

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do not install any unit with damaged, incomplete, or substitute parts.

NOTE: FOR MODEL 6000TR ONLY:

These fireplaces are shipped from the factory with a BTU rating of 27,000 BTU’s. The fireplace can be installed with the vent pipe coming off the top of the unit or the rear of the unit. If you install the unit with the vent pipe coming off the top of the unit, you may run the unit at 31,000 BTU (NG) (30,000 BTU LP), replace the burner orifice with the orifice included in the manual bag. DO NOT REPLACE THE ORIFICE

IF YOU ARE USING THE REAR SET OF VENT COLLARS.

Changing the orifice when venting out the top.

1.Remove the glass door.

2.Using a 1/4” socket, remove the sheetmetal screws holding the long refractory clip in place. Remove the logs and refractory as one piece.

3.Remove the protective plastic from the logs.

4.Remove the two sheetmetal screws holding the burner and remove the burner.

5.Replace the burner orifice with the orifice in- cluded in the plastic manual bag (#36DMS for natural gas or #51DMS for propane). Be careful to hold the brass elbow so you don’t kink the aluminum tube.

6.Reverse the steps to replace the burner, logs, refractory, and clip.

The vent system components and trim doors are shipped in separate packages. The gas logs may be packaged separately and must be field installed.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and may present a fire hazard.

2

Getting

Started

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Heat-N-Glo Safety and Warning Information Contents High Altitude Installations Installation CodesApprovals and Codes Approval Listings CodesGetting Started If YOU are Using the Rear SET of Vent CollarsANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000ARCH Fireplace Ceiling Installing the Fireplace Step LocatingClearance Requirements Model Step Framing FireplaceAt Wall Firestops Identifying Vent Components Step Installing Vent SystemVent System Approvals DV-90D Straight UP Corner Installation Venting with ONE 1 90 Elbow For 6000TR & 6000XLT-CDN Venting with TWO 2 90 Elbows 6000ARCH Venting with TWO 2 90 o ElbowsVenting with three 90 elbows Venting with Three 3 90 Elbows Venting Out the Top Vent Installing Vent Components For Model 6000TRVenting Out the Rear Vent Attaching the First Vent Component to the Starting Collars Attach the First Vent Component to the Starting CollarsContinue Adding Vent Components Adding Venting Components 3. Install Support BracketsInstall Firestops Installing Support Brackets12 Hole and Vent Pipe 11 Hole and New Framing Members Attic Firestop Vent TerminationRound & Trapezoid Termination Caps If Exterior Walls are Finished with This also pertains to vertical vent systems installed Minimum Height from Roof to Lowest Discharge Opening Step Gas Control Systems Step Positioning Leveling, Securing FireplaceStanding Pilot Ignition System Direct Spark Ignition DSI SystemGas Controls Systems Step Gas Supply LinePressure Natural Gas Propane Step Gas Pressure RequirementsFor Standing Pilot Ignition Wiring Step WiringFan Wiring Diagram For Direct Spark Ignition DSI WiringStep Finishing MicroswitchIs found on model 6000ARCH onlyHearth Extensions Step Installing Trim Logs, Ember MaterialInstalling the Trim Placing the Ember Material Positioning the LogsModel 6000TR Glass Assembly Double-check for gas leaks Double-check for faulty componentsStep Before Lighting Fireplace After InstallationMaintaining and Servicing Your Fireplace Fireplace MaintenanceBurner Flame Patterns Standing Pilot with Robertshaw Controls only Replacement Parts AccessoriesPart Part Description Part Number Standing Pilot with S.I.T. controls onlyBoth Standing Pilot and DSI Ignition DSI Ignition Only6000XLS 22 X 22 X6000XLT-CDN 22 X 6000ARCH 22 XAccessory Part Description Part Number

6000TR, 6000XLT-CDN, 6000XLS, 6000ARCH specifications

The Heat & Glo LifeStyle 6000 series offers a modern approach to home heating with its sleek designs and advanced technologies. The models within this series, including the 6000XLT-CDN, 6000TR, 6000XLS, and 6000ARCH, are designed for versatility and performance, catering to various aesthetic preferences and functional needs.

One of the standout features of the LifeStyle 6000 line is its linear design, which provides a contemporary aesthetic that fits seamlessly into any room. The 6000XLT-CDN model features a narrow, linear shape, making it an eye-catching centerpiece while providing efficient heating. The 6000TR offers a traditional configuration, with a classic appeal that remains timeless. The 6000XLS takes it a step further by incorporating an elongated view, while the 6000ARCH incorporates an arch design that adds architectural elegance.

Each model is equipped with Heat & Glo’s advanced LED lighting technology, which enhances the visual impact of the flames and creates a warm ambiance. This technology not only provides better illumination but also increases energy efficiency, allowing homeowners to enjoy the soothing glow without excessive energy consumption.

The series is also noted for its Smart Home compatibility, allowing users to control their fireplaces remotely through mobile devices. This feature adds convenience, enabling homeowners to adjust settings, monitor performance, and even program their fireplaces to suit their schedules.

Safety is paramount, and these models come equipped with advanced safety features, including a child lock and automatic shut-off systems. This ensures peace of mind for families while maintaining an inviting atmosphere.

Additionally, the LifeStyle 6000 series supports a range of fuel options, including gas and ethanol burners, providing flexibility according to user preferences and needs. With adjustable flame height and fan speed, users can customize their heating experience to match their comfort levels.

In summary, the Heat & Glo LifeStyle 6000 series blends style with functionality. With its modern designs, cutting-edge technology, and safety features, it provides a luxurious and efficient heating solution that enhances any living space. Whether you’re seeking a contemporary focal point or a traditional warmth, the 6000 series offers models that meet diverse needs while delivering exceptional performance.
Top Page Image Contents