White Rodgers 1F95-0671 DS On Off Selects Automatic Daylight Saving Time option, Heat To L

INSTALLER/CONFIGURATION MENU

21	20	18	MENU	dS (On)	Off	Selects Automatic Daylight Saving Time option
22	21	19	MENU	(OFF)	L, P, Limit	Selects one of 3 Keypad Lockout confi gurations
				Keypad Lockout		L - Total Keypad Lockout
						P - Partial Keypad Lockout
						(Up and Keys still work)
						Limit - Limited Temperature Range
			MENU	(000)	1-999	Selects personal lockout code. 000 is NOT A
				Keypad Lockout		VALID CODE.
23	22	20	MENU	L Heat	L 62 to L 98	Select Limited HEAT Range Temperature
				(99)
24	23	21	MENU	L Cool	L 46 to L 82	Select Limited COOL Range Temperature
				(45)
25	24	–	MENU	CO	06-50	Selects outdoor Compressor OFF temperature
				(05)		(Balance Point temperature). 05 disables fea-
						ture. Outdoor Remote required
			MENU	(dF)	EA	Selects between dF (dual Fuel) or EA (Electric
						Aux) only available if CO is greater than 05
			MENU	Cd		Selects Compressor delay OFF time in seconds
				(60)		(only if dF is selected)
26	25	–	MENU	AO		Selects AO (Auxiliary OFF) temperature. Fea-
				(80)		ture disabled if 80 is selected. Outdoor Remote
						required
27	26	22	MENU	Change Filter (OFF)	On	Selects Filter Change-out Indicator On or OFF.
			MENU	Change Filter (200 h)	25-1975 h	Change Filter time in 25 hour increments. This
						menu only appears if On is selected in above.
28	27	23	MENU	(OFF)	On	Selects UV Lamp
				Change UV Lamp		Timer: On/OFF
			MENU	(350)	25-1975	Selects number of Days between
				Change UV Lamp		changing UV Lamp
29	28	24	MENU	Cool On (o)	Heat On (b)	Selects operation of the reversing valve terminal
						(O/B) output as an O or B terminal
30	29	27	MENU	RUN SCHED		Returns to Normal Operation

1)This control can be configured for:

MS 2 – Multi-Stage System (no heat pump)

HP 1 – Heat Pump with one stage of compressor HP 2 – Heat Pump with two stage compressor or two

compressor system, Gas or Electric backup SS 1 – Single Stage System

2)GAS or Electric (ELE) fan operation. If the heating system requires the thermostat to energize the fan, select ELE. Select GAS if the heating system energizes the fan on a call for heat.

3)Select Cool Savings™ value – Selects the amount of adjustment for the Cool Savings™ feature in Cool mode with 1 (1°) being the least amount of adjustment and 6 (6°) being the most amount of adjustment. Default value is 3. Cool Savings is an optional energy saving feature that can reduce your cooling costs. It is based on the principal that lower indoor humidity makes a slightly higher tem- perature feel more comfortable. Cool Savings operates during periods of high demand which normally occur on the hottest summer days when a cooling system may run for hours to reach the thermostat setting. Long cooling run times also lower the indoor humidity. Cool Savings, very slowly, adjusts the setpoint temperature to make the setpoint closer to the displayed room temperature, to a maximum of the number of degrees you select. Adjust- ing the setpoint temperature over a long cooling run time allows the system to reach your set temperature and turn off. The room temperature will actually be higher than the

thermostat displays but the reduction in humidity will allow comfort at the slightly higher temperature.

To turn this feature on in the Cool mode press Cool Savings. The display will show “Save” next to the set- point temperature. When Cool Savings is making adjust- ments to the room temperature display “Save” will be

flashing and the displayed room temperature may vary within the adjustment range you selected.

If "Save" is not displayed and this feature is OFF, no change will occur when the cooling system is continuously running during periods of high demand.

4)Energy Management Recovery: (this step is skipped if configured to be non-programmable).

Energy Management Recovery (E) On enables the ther- mostat to start heating or cooling early to make the building temperature reach the program setpoint at the time you specify. Heating will start approximately 5 minutes early (15 minutes for heat pump) for every 1° of temperature required to reach setpoint.

Example: E On is selected and your heating is pro- grammed to 65° at night and 70° at 7 AM. If the building temperature is 65°, the difference between 65° and 70° is 5°. Allowing 5 minutes per degree, the thermostat setpoint will change to 70° at 6:35 AM. Cooling allows approxi- mately 15 minutes per degree, because it takes longer to reach set temperature.

7