Operating Your Thermostat, Fan Operation

INSTALLER/CONFIGURATION MENU

24)Limited Cool Range – This feature provide a minimum setpoint temperature for cool. The default setting is 45°F. It can be changed between 46°F and 82°F by pressing the

or button.

25)Select Compressor Off (CO) Feature Using Outdoor Sensor – This feature is applicable only in heat pump modes and with an outdoor sensor installed and enabled. When CO is enabled by selecting a temperature >05°F (-15°C), the thermostat will use the outdoor sensor tem- perature to determine when to switch to gas heat and shut down the compressor.

When the outdoor temperature goes below the selected temperature, the gas heat will begin. Default is 05 (Off or disabled), but can be set in the range of 06 to 50 using the

or buttons.

Select dF or EA – If CO is set > 05°F (-15°C), select dF (default) if your system has a fossil fuel (gas or oil) Auxil- iary heat. Select EA if your system has Electric Auxiliary heat and you want the compressor to continue to run while calling for Auxiliary stage.

Select Compressor Delay (Cd) – If dF is selected, after the auxiliary heat is turned on, the compressor(s) shut down is delayed for the time selected (in seconds). This delay is factory set to 60, but can be set in the range of 0

to 99 using or buttons.

26)Select Auxiliary Off (AO) – This feature is applicable only in heat pump modes and with an outdoor sensor installed and enabled. Select the temperature that will inhibit the auxiliary heating stage. As long as the outdoor tempera- ture is above the setpoint, the auxiliary heat will not turn on. The default setting is 80, but can be set in the range of 35 to 79. A setting of 80 disables this feature.

27)Select Filter Replacement Reminder and Set Run Time Select the "Change Filter" reminder On or OFF. If se- lected On, press MENU to select the time period from 25 to 1975 hours in 25 hours increments. In a typical system, 200 hours (default) of run time is approximately 30 days. After the selected time of blower operation, the thermostat will display "Change Filter" as a reminder to change or

clean your air ﬁ lter. When "Change Filter" is displayed, press MENU or RUN SCHED button to clear the display and restart the time to the next ﬁ lter change.

28)Change UV Lamp – This feature allows the thermostat to display the words "Change UV Lamp" (Call for Service of UV bulb) after a set time of UV bulb operation. This is a reminder to maintain your UV system at optimum level of operation. When enabled the factory set interval for "Change UV Lamp" to be displayed is 350 days of UV bulb operation and can be adjusted in 25 day increments. This should be adjusted with respect to the bulb's recom- mended maintenance schedule.

When "Change UV Lamp" is displayed, you can clear it by pressing MENU.

29)Select Reversing Valve Output – The O/B option is factory set at "O" position. This will accommodate the majority of heat pump applications, which require the changeover relay to be energized in COOL. If the thermo- stat you are replacing or the heat pump being installed with this thermostat requires a "B" terminal, to energize the changeover relay in HEAT, the O/B option should be set at "B" position.

OPERATING YOUR THERMOSTAT

Check Thermostat Operation

NOTE

To prevent static discharge problems, touch side of thermostat to release static build-up before touching any keys.

If at any time during testing your system does not operate properly, contact a qualiﬁ ed service person.

Fan Operation

If your system does not have a G terminal connection, skip to

Heating System.

1.Turn on power to system.

2.Press FAN button to select ON. The blower should begin to operate.

3.Press FAN button to select AUTO. The blower should stop immediately.

!CAUTION

Do not allow the compressor to run unless the com- pressor oil heaters have been operational for 6 hours and the system has not been operational for at least 5 minutes.

Heating System

1.Press SYSTEM button to select Heat. If the auxiliary heating system has a standing pilot, be sure to light it.

2.Press to adjust thermostat setting to 1° above room temperature. The heat pump system should begin to oper- ate. The display should show “System On”. However, if the system conﬁ guration is set to HP1 or HP2 and setpoint temperature display is ﬂ ashing, the 5 minute compressor lockout feature is operating (see Conﬁ guration menu, item 11).

3.Adjust temperature setting to 3° above room temperature. If your system conﬁ guration is set at MS2, HP2 or HP1, the auxiliary heat system should begin to operate and the display will show “System On +2”.

4.Press to adjust the thermostat below room tempera- ture. The heating system should stop operating.

1F95-0671 specifications

The White Rodgers 1F95-0671 is a versatile and advanced programmable thermostat designed primarily for residential heating and cooling systems. This innovative device provides homeowners with the ability to manage their indoor climate efficiently while maximizing energy savings.

One of the standout features of the 1F95-0671 is its user-friendly interface, which includes a large, easily readable touchscreen display. This modern touch interface simplifies temperature adjustments and programming, making it accessible for users of all ages. The display features bright, clear graphics that provide real-time temperature readings, system status, and schedule reminders.

The thermostat offers a 7-day programmable schedule, allowing users to set different temperature profiles for each day of the week. This flexibility ensures that you'll be comfortable when you're home while saving energy by reducing heating and cooling when the house is empty. The 1F95-0671 also includes a copy feature, enabling users to quickly replicate settings from one day to another, making programming even more convenient.

Equipped with advanced technology, the White Rodgers 1F95-0671 is compatible with multi-stage heating and cooling systems, including gas, oil, electric, and heat pump systems. Its adaptive recovery feature learns how long it takes to reach the desired temperature and adjusts the start time accordingly, increasing overall comfort without wasting energy.

Another key characteristic of this thermostat is its ability to monitor indoor humidity levels. This feature is especially beneficial in regions with extreme weather, providing an added layer of comfort while optimizing HVAC system performance. Users can set humidity levels independently of temperature, enhancing overall home comfort.

Energy efficiency is further promoted through the inclusion of Energy Star ratings, helping users track their energy consumption. The thermostat's smart alerts notify users of maintenance reminders, such as filter changes or system service needs, ensuring HVAC systems operate at their peak performance.

Wireless connectivity is another significant advantage of the 1F95-0671, allowing users to control their home environment remotely using compatible mobile devices. This feature offers a level of convenience and control that aligns with the modern digital lifestyle, providing peace of mind whether at home or away.

In summary, the White Rodgers 1F95-0671 thermostat combines user-friendly functionality, advanced heating and cooling technologies, and energy-efficient performance, making it an excellent choice for homeowners looking to optimize their indoor climate. Its robust features and smart connectivity set it apart as a leading option in the programmable thermostat market.