OPERATING YOUR THERMOSTAT
Emergency System
EMER bypasses the Heat Pump to use the heat source wired to terminal W/E on the thermostat. EMER is typically used when compressor operation is not desired, or you prefer
1.Press SYSTEM button to select EMER. “EMER” will fl ash on the display.
2.Press to adjust thermostat setting above room temperature. The Emergency heating system will begin to operate. The display will show “System On” fl ashing “EMER” and “HEAT” to indicate that the Emergency sys- tem is operating.
3.Press to adjust the thermostat below room tempera- ture. The Emergency heating system should stop operat- ing.
Choose the System Setting
(Cool, Off, Heat, Emer, Auto)
Press the SYSTEM button to select:
Heat: Thermostat controls only the heating system.
Off: Heating and Cooling systems are off.
Cool: Thermostat controls only the cooling system.
Auto: Auto Changeover is used in areas where both heating and cooling may be required on the same day. AUTO allows the thermostat to automatically select heating or cooling depending on the indoor temperature and the selected heat and cool temperatures. When using AUTO, be sure to set the Cooling temperatures more than 1° Fahrenheit higher than the heating temperature.
Emer: Setting is available only when the thermostat is confi g- ured in HP1 or HP2 mode.
!CAUTION
To prevent compressor and/or property damage, if the outdoor temperature is below 50°F, DO NOT operate the cooling system.
Cooling System
1.Press SYSTEM button to select COOL.
2.Press to adjust thermostat setting below room tem- perature. The blower should come on immediately on high speed, followed by cold air circulation. The display should show “System On”. If the setpoint temperature display is fl ashing, the compressor lockout feature is operating (see Confi guration menu, item 5).
3.Adjust temperature setting to 3° below room temperature. The second stage cooling should begin to operate and the display should show “System On +2”.
4.Press to adjust the temperature setting above room temperature. The cooling system should stop operating.
Choose the Fan Setting (Auto or On)
Fan Auto is the most commonly selected setting and runs the fan only when the heating or cooling system is on.
Fan On selection runs the fan continuously for increased air circulation or to allow additional air cleaning.
Fan Prog On indicates that the fan is programmed to be on for the entire period. The Prog Fan On can be overridden to have the fan cycle with the system. Press the FAN but- ton to change the fan to Auto. The fan programming will be overridden until the next program period begins or until Run Schedule is pressed.
Manual Operation for
Non-Programmable Mode
Press the SYSTEM button to select Heat or Cool and use the buttons to adjust the temperature to your desired setting. After selecting your desired settings you can also press the SYSTEM button to select AUTO to allow the thermostat to automatically change between Heat and Cool.
Manual Operation (Bypassing the Program) Programmable Mode
Adjust the temperature wherever you like and then press the HOLD button. This will override the program. The HOLD feature bypasses the program and allows you to adjust the temperature manually, as needed. Whatever temperature you set in HOLD will be maintained 24 hours a day, until you manually change the temperature or press Run Schedule to cancel HOLD and resume the programmed schedule.
Program Override (Temporary Override)
Press buttons to adjust the temperature. This will override the temperature setting for a two hour override period.
Example: If you turn up the heat during the morning program, it will be automatically lowered later, when the temporary hold period ends. To cancel the temporary setting at any time and return to the program, press Run Schedule.
If the SYSTEM button is pressed to select AUTO the thermostat will change to Heat or Cool, whichever ran last. If it switches to heat, but you want cool, or it changes to cool, but you want heat, press both buttons simultaneously to change to the other mode.
PROGRAMMING
Set Current Time and Day
1)Press Menu key to enter installer menu. Then press Time once to indicate hour & AM or PM designation in clock display.
2)Press and hold either the or button until you reach the correct hour and AM or PM designation.
3)Press Time again to display minutes only in clock display.
4)Press and hold either the or button until you reach the correct minutes.
5)Press Time once again to display year.
6)Press and hold either the or button until you reach the correct year.
7)Press Time once again to display month.
8)Press and hold either the or button until you reach the correct month.
9)Press Time once again to display date of the month along with day of the week at top row (which is auto- matic).
10)Press and hold either the or button until you reach the correct day of the month and day of the week is automatically calculated and displayed at the top row.
11)Press Run Schedule once; now the display will show the correct time and room temperature.
9