Desa V)V42EPA(1) SERIES, V)V42ENA(1) SERIES installation manual Inspecting Burners, Pilot Assembly

Page 26

26

OPERATING FIREPLACE

Operating Optional Blower Accessory

INSPECTING BURNERS

Pilot Assembly

Burner Flame Pattern

OPERATING FIREPLACE

Continued

OPERATING OPTIONAL

BLOWER ACCESSORY

Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the left just inside the louver panel.

The BK manual blower and the BKT thermostatically-con- trolled blower have an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

Note for BKT Only: If you are using BKT blower with optional thermostat (wall mounted or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.

The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions that will hinder the flow of air.

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame. Alterations may have occurred during shipping and handling. The pilot is located on the back right hand side of the burner.

The flame must envelope 1/4" of top of the ignitor/sensor and grounding stem.

If your pilot assembly does not meet these requirements:

•Turn the adjustment screw marked PILOT clockwise to decrease or counterclockwise to increase the flame to proper size (see Figure 49, page 25). Do not remove the adjustment screw.

•see Troubleshooting, pages 28 and 29

Pilot Burner

Sensing Rod

 

 

Ignitor/Sensor

Figure 51 - Correct Pilot Flame Pattern

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions.

If the vent configuration is installed incorrectly, the flames will lift or "ghost". This can be dangerous. Inspect the flames after installa- tion to ensure proper installation and performance.

Figure 52 shows a typical flame pattern.

If burner flame pattern differs from that described:

•turn fireplace off (see To Turn Off Gas to Appliance, page 25)

•see Troubleshooting, pages 28 and 29

Figure 52 - Typical Flame Pattern

For..com

111907-01B

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Your Safety What to do if YOU Smell GAS OWNER’S Operation Installation ManualFor Your Safety Table of Contents Safety InformationProduct Identification Local CodesLocation and Space Requirements Product FeaturesPRE-INSTALLATION Preparation Clearances Framing and FinishingLocation of Termination CAP Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationInstalling Horizontal Vent Cap Noncombustible Exterior Horizontal Termination Configurations Ground Floor InstallationCorner Installation Venting with Two 90 Elbows Installation for Vertical Termination Flat Ceiling InstallationVertical Termination Configurations High Altitude Installation Number DescriptionCheck GAS Type Fireplace InstallationInstalling Optional Blower Accessory Attaching Speed Control to Firebox Model BKT Installation Blower Wiring DiagramInstalling GAS Piping to Fireplace Location Installation Items NeededPressure Testing Gas Supply Piping System Connecting Fireplace to GAS SupplyInstallation Items Needed Checking GAS ConnectionsREMOVING/REPLACING Glass Door Pressure Testing Fireplace Gas ConnectionsCleaning Glass Door Removing Louver PanelsInstalling Optional Brick Liner Models BL42DASA, BL42DHASA Installing LOGS, Lava Rock and Glowing EmbersInstalling Log No and Log No Optional Remote Control Wiring DiagramWall Switch Installation Lighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To ApplianceInspecting Burners Operating Optional Blower AccessoryPilot Assembly Burner Flame PatternPilot and Burners Cleaning MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible Cause RemedyObserved Problem Possible Cause Illustrated Parts Breakdown ModelsParts List Description QTYBurner Assembly for Models VV42ENA1, VV42ENSA1 KEY Part Number Description QTY Technical Service Replacement PartsService Hints SpecificationsOwners Registration Form Postage Required Accessories Warranty Information

V)V42EPA(1) SERIES, V)V42ENA(1) SERIES specifications

The Desa V)V42EPA(1) and V)V42ENA(1) series represent a significant advancement in energy-efficient technologies, emphasizing performance, environmental sustainability, and user comfort. These innovative products have been meticulously designed for various applications, catering to residential, commercial, and industrial energy needs.

One of the standout features of the V)V42EPA(1) and V)V42ENA(1) series is their exceptional energy efficiency. Equipped with advanced integrated circuit technology, these devices optimize power consumption, reducing utility bills while minimizing carbon footprint. The utilization of cutting-edge materials in their construction ensures durability and long-lasting performance, making them an excellent investment for users seeking reliability.

The V)V42EPA(1) series integrates innovative heat exchange technology, allowing for superior thermal performance. This feature ensures quick heat delivery, enhancing overall efficiency while maintaining a comfortable indoor environment. Additionally, the models within this series are designed to operate quietly, making them suitable for settings where noise reduction is paramount, such as homes and offices.

Meanwhile, the V)V42ENA(1) series boasts advanced air filtration capabilities. These units incorporate sophisticated purification systems that significantly reduce allergens, dust, and other pollutants from the air. This feature not only contributes to improved indoor air quality but also facilitates a healthier living or working environment.

Another critical characteristic of both series is their user-friendly interface. They are equipped with intuitive control panels that simplify adjustments and enhance user experience. Remote control capabilities further allow users to manage settings from a distance, adding convenience to day-to-day operation.

The smart technology integration in the V)V42EPA(1) and V)V42ENA(1) series enables connectivity with smart home systems. This functionality allows users to monitor and control their energy consumption seamlessly, further promoting an eco-friendly lifestyle.

Both series are also designed with sustainability in mind. They utilize refrigerants with lower global warming potential, aligning with international environmental standards. This commitment to sustainability not only benefits the planet but also ensures compliance with regulatory requirements.

In conclusion, the Desa V)V42EPA(1) and V)V42ENA(1) series offer a blend of efficiency, comfort, and eco-friendliness. With their advanced technologies, user-centric design, and commitment to sustainability, these series set a benchmark in the energy solutions market, making them ideal choices for anyone looking to improve their energy management and overall indoor environment.
Top Page Image Contents