Desa EFS33PR Cleaning Maintenance, Cleaning Burner Injector Holder and Pilot AIR Inlet Hole, Logs

Page 19

CLEANING AND MAINTENANCE

Cleaning Burner Injector Holder and Pilot Air Inlet Hole Logs

19

CLEANING AND

MAINTENANCE

WARNING: Turn off fireplace and let cool before cleaning.

CAUTION: You must keep control areas, burner, and circulating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding mate- rial, pet hair, etc.

Injector Holder

Ports/Slots

Burner

Tube

Primary Air

Inlet Holes

Figure 38 - Injector Holder On Outlet Burner Tube

CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry com- pressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the direc- tions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1.Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2.Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 38).

3.Blow air through the ports/slots and holes in the burner.

4.Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5.Blow air into the primary air holes on the injector holder.

6.In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 39). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Ports/Slots

Burner

Tube

Pilot

Assembly

Pilot Air

Inlet Hole

Figure 39 - Pilot Inlet Air Hole

LOGS

•If you remove logs for cleaning, refer to Installing Logs, page 14, to properly replace logs.

•Replace log(s) if broken or chipped (dime-sized or larger).

For morevisit www..com

107172-01F

Page 18 Page 20
Image 19
Page 18 Page 20
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsProduct Identification Log Base Assembly VSGF33NR ShownAIR for Combustion and Ventilation Product FeaturesLocal Codes UnpackingConfined and Unconfined Space Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Unusually Tight ConstructionVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Electrical Hookup InstallationInstalling Hood Check GAS TypeAssembling and Attaching Optional Brass Trim Installation ClearancesConventional Fireplace Installation Included with Mantel AccessoryPlacing Hearth Base Accessory Against Wall Mantel Clearances for Built-In Installation BUILT-IN Fireplace InstallationInstallation Items Needed Installing GAS Piping to Fireplace LocationGas Connection Connecting Equipment Shutoff Valve to Heater ControlPressure Testing Fireplace Gas Connections Pressure Testing gas Supply Piping systemChecking GAS Connections Slide the grooves in the back of the rear log #3 against Installing LogsOperating Fireplace For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureOptional Remote Operation Ghrcta Series Operation Optional Blower OperationMain Burner Inspecting BurnersPilot Flame Pattern Front Burner Flame PatternCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceLogs Observed Problem Possible Cause Remedy TroubleshootingMaintenance, For Visit Com Service Hints Wiring DiagramSpecifications Replacement PartsIllustrated Parts Breakdown LOG Base Assembly EFS33NR, VSGF33NR4Parts List FIREPLACE17 EFS33NR,VSGF33NR EFS33PR, VSGF33PR KEY Part Number Description QTY Fireplace EFS33NR, VSGF33NR EFS33PR, VSGF33PRAccessories Hardwood Hearth Base Corner Hearth BaseLaminate Trim for Hearth or Mantel Not Shown Receiver and HAND-HELD Remote Control KIT GHRC/CGHRC SeriesWALL-MOUNT Thermostat Switch GWMT1 WALL-MOUNT ON/OFF Switch GWMS2Owners Registration Form Tape 107172-01F Warranty Information

EFS33PR specifications

Desa EFS33PR is an innovative electric fireplace solution designed to bring warmth and ambiance to modern living spaces. With its sleek design and advanced features, this unit stands out as a versatile and efficient heating appliance. One of the main highlights of the EFS33PR is its realistic flame effect, which utilizes cutting-edge LED technology to simulate the appearance of a glowing fire. This feature allows users to enjoy the visual appeal of a traditional fireplace without the mess, smoke, or maintenance associated with wood-burning units.

Another significant characteristic of the EFS33PR is its adjustable heat settings. The fireplace offers multiple heat output levels, allowing users to customize the warmth according to their preferences and the specific requirements of their space. This flexibility ensures efficient energy consumption, making the fireplace not only a stylish addition to home decor but also a practical heating solution.

The EFS33PR is designed with user convenience in mind. It comes equipped with a remote control, enabling users to operate the fireplace from the comfort of their sofa or bed. This added convenience is particularly appreciated during colder months when getting up to adjust settings may not be ideal. Additionally, the fireplace is equipped with a timer function, allowing users to set it to turn on or off after a specified duration.

Safety is another priority in the design of the Desa EFS33PR. The unit is built with overheat protection, ensuring that it operates within safe temperature limits. This feature provides peace of mind, especially in homes with pets or children, as it minimizes the risk of accidental burns or overheating.

The EFS33PR is also designed for easy installation. It can be mounted on the wall or placed in a corner, making it a versatile option for different room layouts. Its contemporary aesthetic is complemented by a range of color options, ensuring it can blend seamlessly into various interior styles.

In conclusion, the Desa EFS33PR electric fireplace combines modern technology, convenience, and safety features, making it an ideal choice for those seeking an efficient and stylish heating solution. Whether enhancing the decor of a living room or adding warmth to a bedroom, the EFS33PR offers a perfect blend of functionality and elegance.
Top Page Image Contents