Desa EFS33PR installation manual Placing Hearth Base Accessory Against Wall

Page 9

INSTALLATION

Continued

cabinet/corner mantel directly on the floor. The corner mantel accessory cannot be installed with the G3333F/G3334U/G3004W/ G3335F/G3007U hearth base. The corner mantel can be paired with the G3008F/G3009U/G3010F corner hearth base. If mounting fireplace and cabinet or corner mantel to the floor, an optional G3005J/3005S/3005B Slim Base kit may be installed.

1.Assemble cabinet mantel, hearth base, and trim accessories. Assembly instructions are included with each accessory.

2.When installing blower, install a properly grounded, 120 volt three-prong electrical outlet at fireplace location if an outlet is not there. If possible, locate outlet so cabinet mantel will cover it when installed (see Figure 9).

3.Install gas piping to fireplace location. This installation includes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Installing Gas Piping to Fireplace Location, pages 11 and 12.

4.Place hearth base accessory against wall at installation loca- tion. Cut an access hole in hearth top to run flexible gas line to fireplace (see Figure 9). Make sure to locate access hole so cabinet mantel will cover it when installed. Note: You can secure base to floor using wood screws. Countersink screw heads and putty over.

5.Route flexible gas line through access hole in hearth base.

6.Center cabinet mantel on hearth base (see Figure 10). Make sure mantel is flush against wall.

7.Break off nailing flanges (see Figure 11) with hammer or pliers.

8.Place cardboard or other protective material on top of hearth base. Carefully set fireplace on protective material, with back of fireplace inside mantel opening.

9.Attach flexible gas line from fireplace gas regulator to gas sup- ply. See Connecting Fireplace to Gas Supply, page 12.

10.If blower is installed, route blower electrical cord through ac- cess holes in either side of fireplace. Note: Bushing may be moved if necessary. Plug electrical cord into electrical outlet.

11.Carefully insert fireplace into cabinet mantel. Be careful not to scratch or damage hearth base, cabinet mantel, or any lami- nate trim on hearth base. Remove protective material from top of hearth base and from front of fireplace (if any). Note: You can secure fireplace to hearth or floor. Open lower louver. Locate screw holes in bottom of base. Tighten wood screws through these holes and into hearth or floor.

12.Check all gas connections for leaks. See Checking Gas Con- nections, page 13.

INSTALLATION

9

Conventional Fireplace Installation (Cont.)

 

 

Rigid Pipe and Gas

Shutoff Valve

Electrical

Outlet

 

Gas Line

Hearth

Access

Base

Hole

Figure 9 - Placing Hearth Base Accessory Against Wall

Cabinet

Mantel

Figure 10 - Installing Cabinet Mantel

Nailing

Flanges

Figure 11 - Location of Nailing Flanges

Figure 12 - Inserting Fireplace Into Cabinet Mantel

For morevisit www..com

107172-01F

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsProduct Identification Log Base Assembly VSGF33NR ShownLocal Codes Product FeaturesUnpacking AIR for Combustion and VentilationDetermining FRESH-AIR Flow for Heater Location Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installing Hood InstallationCheck GAS Type Electrical HookupConventional Fireplace Installation Installation ClearancesIncluded with Mantel Accessory Assembling and Attaching Optional Brass TrimPlacing Hearth Base Accessory Against Wall Mantel Clearances for Built-In Installation BUILT-IN Fireplace InstallationInstallation Items Needed Installing GAS Piping to Fireplace LocationGas Connection Connecting Equipment Shutoff Valve to Heater ControlPressure Testing gas Supply Piping system Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections Slide the grooves in the back of the rear log #3 against Installing LogsFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions Manual Lighting Procedure To Turn OFF GAS To ApplianceOptional Remote Operation Ghrcta Series Operation Optional Blower OperationPilot Flame Pattern Inspecting BurnersFront Burner Flame Pattern Main BurnerCleaning Maintenance Cleaning Burner Injector Holder and Pilot AIR Inlet HoleLogs Observed Problem Possible Cause Remedy TroubleshootingMaintenance, For Visit Com Specifications Wiring DiagramReplacement Parts Service HintsIllustrated Parts Breakdown LOG Base Assembly EFS33NR, VSGF33NR4Parts List FIREPLACE17 EFS33NR,VSGF33NR EFS33PR, VSGF33PR KEY Part Number Description QTY Fireplace EFS33NR, VSGF33NR EFS33PR, VSGF33PRAccessories Corner Hearth Base Hardwood Hearth BaseLaminate Trim for Hearth or Mantel WALL-MOUNT Thermostat Switch GWMT1 Receiver and HAND-HELD Remote Control KIT GHRC/CGHRC SeriesWALL-MOUNT ON/OFF Switch GWMS2 Not ShownOwners Registration Form Tape 107172-01F Warranty Information

EFS33PR specifications

Desa EFS33PR is an innovative electric fireplace solution designed to bring warmth and ambiance to modern living spaces. With its sleek design and advanced features, this unit stands out as a versatile and efficient heating appliance. One of the main highlights of the EFS33PR is its realistic flame effect, which utilizes cutting-edge LED technology to simulate the appearance of a glowing fire. This feature allows users to enjoy the visual appeal of a traditional fireplace without the mess, smoke, or maintenance associated with wood-burning units.

Another significant characteristic of the EFS33PR is its adjustable heat settings. The fireplace offers multiple heat output levels, allowing users to customize the warmth according to their preferences and the specific requirements of their space. This flexibility ensures efficient energy consumption, making the fireplace not only a stylish addition to home decor but also a practical heating solution.

The EFS33PR is designed with user convenience in mind. It comes equipped with a remote control, enabling users to operate the fireplace from the comfort of their sofa or bed. This added convenience is particularly appreciated during colder months when getting up to adjust settings may not be ideal. Additionally, the fireplace is equipped with a timer function, allowing users to set it to turn on or off after a specified duration.

Safety is another priority in the design of the Desa EFS33PR. The unit is built with overheat protection, ensuring that it operates within safe temperature limits. This feature provides peace of mind, especially in homes with pets or children, as it minimizes the risk of accidental burns or overheating.

The EFS33PR is also designed for easy installation. It can be mounted on the wall or placed in a corner, making it a versatile option for different room layouts. Its contemporary aesthetic is complemented by a range of color options, ensuring it can blend seamlessly into various interior styles.

In conclusion, the Desa EFS33PR electric fireplace combines modern technology, convenience, and safety features, making it an ideal choice for those seeking an efficient and stylish heating solution. Whether enhancing the decor of a living room or adding warmth to a bedroom, the EFS33PR offers a perfect blend of functionality and elegance.
Top Page Image Contents