Desa CF26NRA Removing Brick Liner Retainer, Assembling Trim, Optional Mantel Installation

Page 11

INSTALLATION

Continued

Note: All vertical

Mantel Shelf

 

 

 

 

measurements

10"

 

 

 

are from top

 

 

 

8"

 

 

 

of fireplace

 

 

 

 

 

 

 

opening to

6"

 

 

 

 

 

 

bottom of

2 1/2"

 

 

 

 

 

 

mantel shelf.

 

 

 

 

Minimum Non-

 

 

 

 

Combustible

 

 

 

 

Material

13"

16"

19"

21"

 

 

 

 

 

 

Figure 8 - Minimum Mantel Clearances

for Built-In Installation

REMOVING BRICK LINER

RETAINER

1.Using Phillips screw driver, remove 2 screws attaching brick liner retainers to vertical sides.

2.Remove brick liner retainers and discard. Replace 2 screws into vertical sides.

ASSEMBLING TRIM

(Trim shipped with mantel)

1. Remove packaging from three pieces of trim.

2. Locate two adjusting plates with set screws, and two shims in the hardware packet.

3. Align shim under adjusting plate as shown in Figure 9.

4. Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 9).

5. Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 9).

6. While firmly holding edges of trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set trim assembly aside for later installation.

Slot

Set Screws

 

Top

 

 

 

 

Trim

 

Shim

Mitered

 

Edge

 

 

Side

Adjusting Trim

Plate

Slot

Figure 9 - Assembling Trim

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the man- tel for assembly instructions. Refer to instructions below for system installation. If using blower ac- cessory (see Accessories, page 35), see installation instructions on pages 12 through 15.

1.Choose location for fireplace and install gas supply line.

2.Remove screen from fireplace by removing screws in each end of screen rod (see Figure 10). Hold screen rod cover while removing five hex head screws underneath hood (see Figure 11). Carefully lift and pull out hood (see Figure 12, page 12).

Figure 10 - Removing Screen

Hood

Screen Rod

Cover

Screw

Figure 11 - Removing Hood Screws

113897-01A

www.desatech.com

11

Image 11
Contents What to do if YOU Smell GAS Table of Contents Safety Information Unpacking Local CodesProduct Identification Product FeaturesRemote Control Accessories Confined and Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Unusually Tight ConstructionVentilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Locating Fireplace InstallationCheck GAS Type Minimum Clearance for Combustible to Wall BUILT-IN Fireplace InstallationAttaching Fireplace to Wall Studs Mantel Clearances for Built-In InstallationTrim shipped with mantel Optional Mantel InstallationRemoving Brick Liner Retainer Assembling TrimRemoving Hood Installing Blower Assembly GA3450TInstalling Blower Bracket Assembly For Built-In Installation Installation Items Needed Connecting to GAS SupplyNatural From Connecting Fireplace to GAS SupplyPropane/LP KPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Test Pressures In Excess Of 1/2 PsigPressure Testing Heater GAS Connections Installing LogsInstalling 9-Volt Battery in Receiver Installing Wireless Remote Control AccessoryLighting Instructions For Your Safety Read Before LightingSelector Switch Flame Operating FireplaceOptional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Series Model Cghrctb ON/OFF Series Model CghrcbInspecting Burners Cleaning MaintenanceExterior Burner Injector Holder and Pilot AIR Inlet HoleCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingSee Cleaning and Mainte On windows Tilation air Gas leak. See Warning Wiring Diagram SpecificationsModels CF26PRA and CF26NRA Illustrated Parts BreakdownParts List 20-1 11-1 20-3 11-2 KEY Part Number Description QTY Parts Central Replacement PartsService Hints Technical ServiceThermostatically Controlled Blower KIT GA3450T Receiver and HAND-HELD Remote Control KIT CghrcbCleaning KIT GCK Equipment Shutoff Valve GA5010Limited Warranty VENT-FREE GAS BAY Front Fireplace Warranty InformationKeep this Warranty

CF26NRA, CF26PRA specifications

Desa CF26PRA and CF26NRA are highly regarded heating appliances designed for efficient and reliable home heating solutions. These units are part of Desa's comprehensive lineup, known for their innovative technology and user-friendly features. Both models are distinct yet share a common commitment to optimizing warmth and comfort in residential spaces.

One of the main features of the CF26PRA and CF26NRA is their impressive heating capacity. These heaters are engineered to deliver significant BTUs, ensuring that even large rooms are heated rapidly and evenly. Both models utilize a forced air distribution system that effectively circulates warmth throughout the living area, eliminating cold spots and providing a consistent, cozy environment.

In terms of design, the CF26PRA and CF26NRA are visually appealing with modern aesthetics that blend seamlessly into various décors. Their compact size allows for flexible placement, whether freestanding or wall-mounted, making them an ideal choice for any room in the home, including living rooms, basements, or even workshops.

Incorporating advanced technologies, these models are equipped with electronic ignition systems, which eliminate the need for manual lighting, ensuring ease of use. Their adjustable thermostat allows homeowners to set the preferred temperature, automatically regulating heat output to maintain comfort while optimizing energy efficiency.

Both the CF26PRA and CF26NRA are constructed with durable materials that enhance their longevity and performance. This robust build is paired with safety features like automatic shut-off and flame failure protection, providing peace of mind for users, particularly in homes with children or pets.

Energy efficiency is another hallmark of these models. They are designed to consume minimal fuel while maximizing output, which helps in reducing monthly heating costs without sacrificing comfort. The CF26NRA, specifically, features an enhanced combustion system, further improving fuel efficiency and lowering emissions.

In conclusion, Desa CF26PRA and CF26NRA are excellent choices for anyone seeking reliable, efficient, and stylish heating solutions. With their user-friendly features, advanced technology, and strong performance characteristics, both models represent a solid investment for maintaining a warm and inviting home during cold weather months. Whether you're upgrading your heating system or looking for a supplemental heater, these models will meet and exceed expectations, keeping every corner of your home comfortably warm.