Desa VFB50NC, V50SH Installation, Continued, Assemble cabinet mantel as instructed

Page 10
1.Assemble cabinet mantel as instructed.

10

INSTALLATION

Built-In Firebox Installation (Cont.)

Installing Firebox Using Optional Mantels Available from Retailer or Custom Built

INSTALLATION

Continued

IMPORTANT: When finishing your firebox, combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top of the firebox. Combustible materials should never overlap the firebox front facing.

Manual background WARNING: Do not allow any combustible materi- als to overlap the firebox front facing.

Nails or

Wood

Screws

Nailing Manual backgroundManual background

Flanges

Figure 7 - Attaching Firebox to Wall Studs

IMPORTANT: Noncombustible materials such as brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.

Manual backgroundWARNING: Do not allow noncombustible materials to cover any necessary openings like louvered slots.

Manual background WARNING: Use only noncombustible mortar or adhesives when overlapping the front facing with noncombustible facing material.

INSTALLING FIREBOX USING OPTIONAL MANTELS AVAILABLE FROM RETAILER OR CUSTOM BUILT

Manual background WARNING: A qualified service person must in- stall firebox. Follow all local codes.

This firebox may be installed using a cabinet mantel against a wall in your home. The firebox and cabinet mantel can be installed directly on the floor. Mantels may be available from your retailer or custom built for your home.

1.Assemble cabinet mantel as instructed.

2.Install gas piping to firebox location. See Installing Gas Line, page 11. You may have to cut an access hole in the floor or wall to run gas line to firebox. Make sure to locate access hole so cabinet mantel will cover it when installed (see Figure 8).

3.Place cabinet mantel on floor in desired location. Make sure mantel is flush against wall.

4.Carefully insert firebox into cabinet mantel. Be careful not to scratch firebox, cabinet mantel, flooring, etc. when installing (see Figure 9).

5.Install and properly test gas log heater. Follow installation in- structions included with the vent-free gas log heater that is being installed.

Cabinet

Mantel Manual background

Gas Line

 

Access Hole

 

(Either Side

Gas

of Firebox)

 

Piping

Figure 8 - Installing Cabinet Mantel (Mantel May Vary From Illustration)

Figure 9 - Inserting Firebox Into Cabinet Mantel (Mantel May Vary From Illustration)

Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundForManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background.Manual backgroundManual backgroundManual backgroundManual background.comManual backgroundManual backgroundManual backgroundManual backgroundManual background

110749-01A

Image 10
Contents TM OWNER’S OPERATION AND INSTALLATION MANUAL UNVENTED VENT-FREE UNIVERSAL FIREBOXSave this manual for future V50S, V50SH, and VFB50NC Vent-FreeFireboxesSAFETY INFORMATION TABLE OF CONTENTSWARNINGS LOCATING FIREBOX PRODUCT FEATURESLOCAL CODES ContinuedFigure 1 - Firebox Dimensions PRODUCT SPECIFICATIONSPRODUCT SPECIFICATIONS Firebox Top ViewAIR FOR COMBUSTION AND VENTILATION PROVIDING ADEQUATE VENTILATIONContinued AIR FOR COMBUSTION AND VENTILATIONAIR FOR COMBUSTION AND VENTILATION VENTILATION AIR AIR FOR COMBUSTION AND VENTILATIONContinued Ventilation Air From Inside BuildingINSTALLATION INSTALLATION CLEARANCESMantel Clearances for Built-InInstallation INSTALLATIONBUILT-INFIREBOX INSTALLATION ContinuedContinued INSTALLATION1.Assemble cabinet mantel as instructed INSTALLING FIREPLACE HOOD AND SCREEN INSTALLATIONINSTALLING GAS LINE INSTALLATION24 25 23 38 32 36 37 ILLUSTRATED PARTS BREAKDOWNILLUSTRATED PARTS BREAKDOWN 11 12PART PARTS LISTPARTS LIST PARTREPLACEMENT PARTS TECHNICAL SERVICEACCESSORIES H50B - 50 Hood - Brushed BrassOWNERS REGISTRATION FORM TAPE Postage RequiredTAPE 2701 Industrial Drive P.O. Box Bowling Green, KYPage Model Serial No Date Purchased WARRANTY INFORMATIONNOT A UPC 2701 Industrial Drive P.O. Box Bowling Green, KY