Vermont Casting SR42, SR36, SC42, SC36 manual Hearth Installation, With Without

Page 16

Majestic Fireplaces® SR/SC Series

9. Hearth Installation

A hearth extension is required to protect a combustible floor in front of the fireplace. Refer to Figure 23 for minimum dimensions and mounting detail.

Note: Hearth Extension must not cover the air inlet opening of a fireplace.

The hearth extension described in Figure 23 must be a durable non-combustible material with a minimum (total) Rt value of 1.09; see Figure 24 for examples. The overall height (above a combustible floor), depth and width must be as indicated, with the extension centered to the fireplace opening.

The top of insulation must be covered with a non- combustible decorative covering or a piece of .018” minimum sheet metal, to protect hearth extension material. (Fig. 23)

Secure the hearth extension to the floor to prevent shifting, using trim molding or other similar means at three (3) outer edges. Seal crack between the fire- place hearth and hearth extension with a non-combus- tible material. (Figs. 23 and 25)

WARNING: HEARTH EXTENSION MUST BE INSTALLED IN ACCORDANCE WITH FIGURE 23 AND MUST NOT COVER THE BOTTOM FRONT OPENING OF THE CIRCULATING MODEL.

Alternate noncombustible materials may be used providing the (total) thermal resistance (Rt value) of the alternate material employed is greater than or equal to R = 1.09. Thermal resistance (R) or thermal conductivity (K), may be obtained from manufacturer of the material. Factors are related by the formula K = 1/R.

T = given thickness

R = thermal resistance for a given thickness (T) K = thermal conductivity

Noncombustible material with a lower R value may be used, provided thickness of material is sufficiently greater to maintain an equivalent (total) thermal resistance (Rt).

Minimum Wall Clearances

WITH

WITHOUT

Noncombustible

Noncombustible

Surround Facing

Surround Facing

Shaded area starts

1/2" away from

4" BRICKedge of unit. (Example material)

 

 

 

4"

 

E

F**

FIREBOX

E

D

 

OPENING

 

 

 

 

 

C**

 

A - Min. clearance

 

 

 

 

to combustible

 

 

 

 

perpendicular wall

 

 

SIDE

 

B - Min. clearance

SIDE

WALL

 

to combustible

WALL

 

 

perpendicular wall when

 

 

 

 

using noncombustible wall shield*

 

 

Combustible material permitted within shaded area.

*Noncombustible wall shield requires 1" Majestic EH2416 insulation (minimum R Value = 1.85) between decorative noncombustible rigid covering and combustible wall.

Minimum height and width is 40" x 40".

**Dimension/degree of angle will vary depending on thickness of noncombustible surround facing.

Minimum Hearth Extension Dimensions

(for On-Site Construction)

 

G

G

 

H

 

 

 

J

 

Seal cracks

 

May install

between the

 

noncombustible

fireplace

 

decorative

and hearth

 

covering

extension with

 

OR .018" min.

noncombustible

 

sheet metal

material

FIREPLACE

 

 

HEARTH

4" MIN.

 

 

COMBUSTIBLE

MINIMUM

Safety strips

FLOOR

INSULATION

must overlap

 

VALUE "R"

¹⁄₂" minimum

 

 

A

B

C

D

E

F

G

H

J

 

 

SR/SC36

16"

12"

48°

41°

18"

14"

7³⁄₄"

16"

48"

 

 

 

406mm

305mm

 

 

457mm

356mm

197mm

406mm

1219mm

 

 

SR/SC42

20"

12"

42°

35°

18"

14"

11¹⁄₂"

20"

61¹⁄₂"

 

 

 

508mm

305mm

 

 

457mm

356mm

292mm

508mm

1562mm

FP594

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 23 Combustible side wall protection and hearth extension dimensions.

16

Image 16
Contents SR36 Safety Information Table Of ContentsSR36 Series Woodburning Fireplace SR42 Series Woodburning Fireplace Chase Installation Elbow ChimneyOffset Planning Information Mounting The FireplacePlanning The Chimney Run Ten Foot RuleInstallation Chase InstallationChimney Supports Insulating Fireplace Enclosure For Cold ClimatesInstalling Electrical Wire for Circulator Models Install Fan Kit AssemblyFraming Option For Circulating Models OnlyStraight-Up Chimney Installation Offset InstallationCeiling Chimney Hole Possible Obstructions Cutting the HoleInstalling Outside Air Kit Positioning, Safety Strips, Securing The FireplaceInstalling The Chimney System Installing the Firestop Spacer Ceiling Hole Proper Firestop Spacer InstallationFor Insulation Shield Elbow StrapContinue Installing Pipe to Complete Run Install Remainder of Chimney SectionsAdditional Ceilings Penetrating the RoofInstalling Top Housing Or Termination Installing Chimney In a ChaseFinishing Finish Wall Front View Side ViewSide Wall Protection TOP ViewHearth Installation With WithoutCommon Materials and Factors Installing Line For Gas Logs Fireplace TOPSR/SC36 SR/SC42 948Accessories TwabrChimney Components RLTSK8LChimney Components cont. Canada Limited Warranty & 30 Year Protection Plan Vermont Castings, Majestic Products

SR36, SR42, SC42, SC36 specifications

Vermont Castings is renowned for producing high-quality wood and gas fireplaces and stoves, with models like the SR36, SC42, SR42, and SC36 standing out for their efficiency, design, and innovative features. These gas inserts offer a perfect blend of performance and aesthetics, making them an ideal choice for any home looking to enhance its ambiance and heating capabilities.

The Vermont Castings SR36 and SR42 are both designed to deliver warmth and comfort while maintaining an elegant and traditional look. The SR36 model boasts a heating capacity of up to 30,000 BTUs, suitable for spaces up to 1,500 square feet, making it an excellent option for mid-sized rooms. The SR42, with a higher BTU output of up to 40,000, is perfect for larger areas, providing exceptional warmth and efficiency.

The SC36 and SC42 models cater to those wanting traditional style with state-of-the-art technology. The SC36 offers similar heating capabilities, ideal for cozy evenings, while the SC42 brings in a larger flame area for a more dramatic effect. Both models feature a large, clear glass front that provides an unobstructed view of the fire, enhancing the room's atmosphere.

One of the standout characteristics of these models is their inclusion of advanced combustion technology, which ensures maximum heat output while minimizing emissions. The EPA-certified design means that users can enjoy an environmentally friendly heating solution without sacrificing performance. Innovative features like the adjustable flame height and thermostat control allow users to customize their experience easily.

Additionally, the Vermont Castings inserts come equipped with a convenient remote control option, allowing homeowners to adjust settings from the comfort of their sofas. The cast iron construction is not only stylish but also ensures durability and excellent heat retention.

In summary, the Vermont Castings SR36, SC42, SR42, and SC36 models represent the ideal fusion of tradition and modern technology in heating solutions. With their high efficiency, beautiful designs, and user-friendly features, these gas inserts provide an unparalleled heating experience, making them a cherished addition to any home.