Vermont Casting SHR42A, SHR52, SHR48, SHR36 manual Framing, Firebrick Installation, Chimney Set-up

Page 9

 

Hard, Flat

 

Surface

 

Insulation

 

Platform

 

FP555SHR

Fig. 10

Insulating between platform and fireplace.

Framing

Framing can be constructed before or after the fireplace is set in place, however, most installers build the frame before setting the fireplace.

Frame fireplace with 2 x 4 lumber or heavier materials. Refer to framing dimensions in Figures 1 - 4 for basic fireplace specifications.

NOTE: Framing should be positioned to accommodate wall covering and fireplace facing material.

Firebrick Installation

For the SHR52 model the firebrick is packed separately and must be installed in the fireplace.

You will need four (4) firebrick, three (3) brick retainers, a phillips head screwdriver, and the grate.

The side and rear firebrick each have a notch in the top of the brick panel. The side firebrick have a notch in the lower front side of each panel. The herringbone pattern faces out of the fireplace always. (Fig. 11)

NOTE: The screens and screen rod smoke baffle as- sembly must be removed and set aside before proceed- ing. Remove the two screws holding the screens place. There are seven screws holding the screen rod smoke baffle in place.

1.Remove the three brick retainers from the combus- tion dome by removing the phillips screws, set aside.

2.Set the left firebrick in place on the left side of the fireplace.

SHR Series Woodburning Fireplaces

Rear Firebrick

Brick

Retainer

Side Firebrick

Front

Notch

FP1234

Fig. 11 SHR52 Firebrick installation.

3.Slide the rear firebrick back into the left corner be- hind the end of the left firebrick. Push both panels back as far as possible into the left side and corner.

4.Swing the right side of the back firebrick into place. Attach the left brick in place using a brick retainer at the top and phillips screw removed earlier.

5.Slide the right firebrick into place as far back as pos- sible. Attach rear firebrick and right firebrick using brick retainers and phillips screws removed earlier.

6.Slide the hearth firebrick into the grate clip. (Fig. 12) The grate will be used as a handle to set the hearth firebrick in place.

7.With the hearth firebrick securely in place in the grate clip, carefully lift the hearth firebrick into the fireplace, set the rear of the firebrick down, then slide back to meet the rear firebrick. Gently set the front of the firebrick in place. Replace screens and screen rod smoke baffle assembly.

Grate

Hearth

Firebrick

Grate Clip

FP1235

 

Fig. 12 Hearth firebrick in place in grate clip.

Chimney Set-up

Since you have already preplanned the chimney run, you should know exactly how the installation is to be accomplished — how much pipe is required, the num- ber of elbows, if any, and type of termination to be used.

20001384

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents SHR Series Table of Contents Safety InformationSHR36 Series Woodburning Fireplace SHR48 Series Woodburning Fireplace Chase Installation 30˚ Elbow Offsets Chimney Requirements Offset InstallationsMounting the Fireplace Planning InformationPlanning the Chimney Run Ten Foot RuleChase Installation InstallationChimney Supports Insulating Fireplace Enclosure for Cold ClimatesFirebrick Installation FramingChimney Set-up Offset Installation Straight-Up Chimney InstallationCeiling Chimney Hole Possible Obstructions Cutting the HoleInstalling Outside Air Kit Positioning, Safety Strips Securing the FireplaceInstalling the Chimney System Installing the Firestop Spacer Ceiling HoleProper Firestop Spacer Installation Installing Top Housing or Termination Install Remainder of Chimney SectionsAdditional Ceilings Penetrating the RoofInstalling Chimney in a Chase FinishingFinish Wall Mantel clearance Facing on fireplace surround flush with finished wall Side Wall Protection Hearth InstallationExample of Determining Hearth Extension Equivalents Example for Common BrickMinimum Wall Clearances Sealing detail Installing Line for Gas LogsSHR36/42A/48/52 Woodburning Fireplace Accessory Description Model No AccessoriesSLTCF11 Limited Warranty & 30 Year Protection Plan CFM Corporation

SHR36, SHR42A, SHR48, SHR52 specifications

Vermont Casting gas fireplaces, including the SHR42A, SHR36, SHR48, and SHR52 models, stand out for their construction quality and innovative technologies. These models are designed to provide not only warmth but also aesthetic appeal, making them an attractive addition to any home.

The SHR series features a variety of sizes to accommodate different spaces, with the SHR36 being the smallest at 36 inches, while the SHR52 is the largest with a 52-inch dimension. These options allow homeowners to choose a model that best fits their room size and heating needs. Each unit prides itself on powerful heating capabilities, efficiently distributing warmth through advanced heat exchanger systems.

One of the standout features of these fireplaces is their use of high-quality cast iron construction. This material not only adds durability but also enhances the fireplace’s ability to retain and radiate heat. As a result, users experience effective and consistent heating, ensuring comfort during colder months.

The Vermont Casting SHR models incorporate state-of-the-art gas burning technology, including dual-flame ports and easy-adjust controls. This technology allows for precise flame adjustment, enabling users to set the ambiance they desire. Additionally, the fireplace's realistic flame presentation creates a cozy atmosphere reminiscent of traditional wood-burning fires.

Another significant characteristic of the SHR series is the option for customization. Homeowners can choose from various decorative front options, styles, and finishes, allowing for a tailored look that blends seamlessly with their existing décor. The cast iron grates and multiple log options enhance the realistic appearance of the fireplace, making it a striking focal point in any room.

Safety features are integral to the design of these fireplaces. With a sealed combustion system, the SHR models ensure that gases are safely vented outside, minimizing the risk of indoor air pollution. The glass doors are tempered, offering extra protection while still allowing for an unobstructed view of the flames.

In terms of efficiency, the SHR series is designed with energy-saving technologies that maximize heat output while minimizing gas consumption. This efficiency not only lowers utility costs but also makes these fireplaces a more environmentally conscious heating option.

In summary, the Vermont Casting SHR42A, SHR36, SHR48, and SHR52 gas fireplaces offer a unique combination of elegance, efficiency, and exceptional heating capabilities. Their durable construction, advanced technology, and customizable features make them a choice that enhances both comfort and style for any home.
Top Page Image Contents