Vermont Casting BR36, BR42, BC42, BC36 manual Positioning, Safety Strips Securing the Fireplace

Page 11

The following table gives firestop spacer model num- bers:

 

Angle of Chimney at Ceiling

Size of Chimney

Vertical

30°

 

8" Flue

SKFS2A

SKFS6A

"SK" Series

14¹⁄" x 14¹⁄"

14¹⁄" x 25¹⁄"

 

(368 mm x 368 mm)

(368 mm x 648 mm)

8" Flue

FS2A

FS6A

"S" Series 3-Wall

17¹⁄" x 17¹⁄"

17⁷⁄" x 29⁵⁄"

 

(445 mm x 445 mm)

(454 mm x 753 mm)

Fig. 13 Ceiling chimney hole sizes necessary for installing firestop spacer.

The inside dimension of the frame must be the same as the hole size selected from Figure 13 in order to provide the required 1¹⁄" (38 mm) of air space between the outside diameter of the chimney and the edges of the framed ceiling hole.

Positioning, Safety Strips,

Securing the Fireplace

Slide fireplace into position.

Lift the fireplace front slightly and slide the metal safety strips under front bottom edge about 1¹⁄" (38 mm), al- lowing the remainder to extend in front of firebox. Over- lap strips at least 1/2" (13 mm) to provide a positive joint. (Flat safety strips are packed with fireplace.) (Fig. 14)

Safety strips are used to ensure that any combustible materials in front of the fireplace are protected even though a noncombustible hearth extension is required.

If fireplace is to be elevated above the floor, a “Z” shaped metal safety strip must be fabricated and used to protect combustible surfaces in front of the fireplace. This “Z” shaped safety strip is not provided but must be fabricated of metal with each horizontal leg at least 1¹⁄" (38mm) wide and equal in length to the metals strips provided with the fireplace.

Note: Safety strips are not required over noncombusti- ble floors where all supports at the base of the fireplace are noncombustible.

Four (4) nailing flanges are supplied with the fireplace (found on the fireplace hearth). To level the box and secure it firmly in place, remove the nailing flanges from the hearth and install at the sides of the fireplace as shown in Figure 15.

Majestic Fireplaces® BR/BC Series

Installing Outside Air Kit

An outside air kit is installed in all BR/BC Series Fire- places. If desired, or if local codes mandate the use of an air kit, then an AK-MST is required to complete the installation (from air kit to the outdoors). If the outside air kit is to be used, the AK-MST MUST be installed BE- FORE the fireplace is enclosed. Refer to the AK-MST instructions for field installation.

Metal Safety Strip (1,2 or 3 pieces)

 

 

Fire-

"Z"

 

 

Place

Safety

 

 

 

Strip

 

���" (13mm)

 

(not supplied)

 

Plat-

 

����"

Min. Overlap

Form

Hearth Ext.

(38mm)

 

 

FP557

 

 

 

Fig. 14 Safety strip installation.

Nail Top

Standoffs

Nail Side-

Nailing

Flanges

FP549

Fig. 15 Fasten fireplace in position.

7412944

11

Image 11
Contents BR/BC Series Table of Contents Safety Information451162mm 45 1162mm 13mm BR42 Series specifications and framing BR42 Series Woodburning FireplaceFront Width Back Width Depth Chase InstallationIllustration Key 30˚ Elbow OffsetsTen Foot Rule Planning InformationMounting the Fireplace Planning the Chimney RunInsulating Fireplace Enclosure for Cold Climates InstallationChase Installation Chimney SupportsOption For Circulating Models Only Installing Electrical Wire For Circulator ModelsInstall Fan Kit Assembly FramingCutting the Hole Straight-Up Chimney InstallationOffset Installation Ceiling Chimney Hole Possible ObstructionsInstalling Outside Air Kit Positioning, Safety Strips Securing the FireplaceProper Firestop Spacer Installation Installing the Chimney SystemInstalling the Firestop Spacer Ceiling Hole Penetrating the Roof Continue Installing Pipe to Complete RunCanadian Requirements for Insulation Shield Additional CeilingsFinishing Finish Wall Install Remainder of Chimney SectionsInstalling Top Housing Or Termination Installing Chimney In a ChaseFacing Material Examples of wall shield insulation Hearth InstallationSide Wall Protection Example for Common Brick Recessed Installation BR/BC36 OnlyExample of Determining Hearth Extension Equiva- lents Gas line access Installing Line For Gas LogItem/Model Number BR/BC Series42GDKDP BR/BC42 AccessoriesRLTSK8 Chimney ComponentsChimney Components cont. Canada For Majestic Fireplaces PRE-ENGINEERED Fireplace Systems Limited Warranty & 30 Year Protection PlanCFM Corporation
Related manuals
Manual 24 pages 9.58 Kb

BC36, BC42, BR36, BR42 specifications

Vermont Castings is renowned for its high-quality, American-made gas stoves, particularly the BR36, BR42, BC42, and BC36 models. These gas-burning appliances are engineered to provide warmth and comfort while seamlessly blending into any home décor.

The BR36 is designed with versatility in mind, featuring a compact 36-inch size that makes it ideal for smaller spaces. It utilizes a 35,000 BTU burner that delivers impressive heat output, ensuring a cozy atmosphere year-round. The innovative burner technology provides direct venting options, ensuring efficient performance and minimal heat loss. The BR36 is further enhanced by Vermont Castings' unique premium cast iron construction, which radiates heat effectively for long-lasting warmth.

The BR42 offers a larger heating capacity, suitable for medium to larger rooms. With a 42-inch size, it boasts a BTU rating of up to 42,000, enabling it to warm expansive areas with ease. The advanced flame technology creates a realistic fire appearance while maintaining efficiency. This model also includes adjustable airflow settings, allowing users to customize the flame height and heat output according to preference.

The BC42 is a standout model that bridges the gap between modern aesthetics and traditional craftsmanship. With a contemporary design, it caters to homeowners who appreciate style without sacrificing efficiency. The BC42 maintains a high heat output with its efficient burner system, producing up to 35,000 BTUs. Its programmable thermostat provides convenience, allowing for precise temperature control and the ability to schedule heating times, making it user-friendly.

Finally, the BC36, like the other models, boasts outstanding features but in a more compact design. It is perfect for urban dwellers and those looking to optimize small living areas. The BC36 retains efficiency and style, providing up to 30,000 BTUs of heat output. This model also includes an easy-to-use control panel and a large viewing area that allows for excellent fire visibility, enhancing the ambiance of any room.

All four models feature Vermont Castings' commitment to sustainability, with many designs adhering to rigorous environmental standards and using clean-burning technology. These gas stoves are not only functional but also designed to enrich the home experience, proving that comfort and elegance can coexist effortlessly. With Vermont Castings' legacy of excellence, the BR36, BR42, BC42, and BC36 models are exceptional choices for anyone seeking reliable heating solutions.