Enviro 50-1033 owner manual Do not interfere with the structural integrity of the walls

Page 25

Initial Installation

QUALIFIED INSTALLERS ONLY

5.Using tin snips, cut the “Support Box” from the top corners down to the roof line, and fold the resulting flaps over the roof sheathing (Figure 36). Before nailing it in to the roof, run a bead of non-hardening mastic around the top edges of the “Support Box”, to make a seal between the box and the roof. Clean out any combustible material from the inside of the “Support Box”.

6.Complete the cathedral ceiling installation by following the same procedures outlined in Steps 4 through 9 for INITIAL

INSTALLATION - VERTICAL INSTALLATION.

Figure 36: Cathedral Ceiling Support Box

Installation.

CORNER INSTALLATIONS:

Do not interfere with the structural integrity of the walls.

When rear venting if a 90° bend is used the maximum horizontal vent that can be used is 6” (152mm) and if a 45° bend is used the maximum horizontal vent that can be used is 12” (305mm). For installations

with a 36” (915 mm) snorkel refer to Figure 37 and INITIAL INSTALLATION - VENT CONFIGURATIONS AND RESTRICTOR

SETTINGS. For other corner installations refer to Figure 38 and INITIAL INSTALLATION - VENT CONFIGURATIONS AND

RESTRICTOR SETTINGS.

 

 

 

Figure 37: Corner installation rear vented with

 

Figure 38: Corner installation top vented.

snorkel.

 

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Consumer InstallerGeneral Safety PrecautionsTable of Contents TOP Vent DV Codes And ApprovalsRear Vent DV Westport Exterior Dimensions SpecificationsOperating Instructions For Your Safetyread Before OperatingNatural Gas Propane Venturi Setting Component Sound & Reason Electronic Ignition Module Location Maintenance And ServiceHandles for Removing Door To ReplaceConversion Kit Installation Kit Parts ListRotate the screw clockwise Venturi adjustment piece welded to the burner venturi tubeQualified Installers only Initial InstallationRound Support Vent Termination Restrictions KIT Components Installation InstructionsManufacturer Trade Name Nominal Sizes Installation of Fireplace Horizontal Vent Kit4DSC Vent Configurations and Restrictor Settings Twist-Lock Connection 51mm at top, 11⁄2 38mm at sides, 11⁄2 38mm at BottomTermination Pipe and elbows may be utilized in the attic, as Support box up through the roof line. GalvanizedOver 18/12 to 20/12 Over 20/12 to 21/12 Follow installation steps 1 & 2 under Initial Do not interfere with the structural integrity of the walls 33a-2002 Test Methods and the Resulting ITS Firebox Top Installation for Top Vented Horizontal Termination Corner InstallationWiring Diagram InstallationCanadian Installations A. InstallationsSpillage Test Venting of a Fireplace Fitted with the Drafthood AdaptorSpill Switch Replacement Automatic Safety Shut DownOptional Finishing To Test Valve Pressures GAS Line ConnectionWiring Diagram For Fan Control Wire Size Max. LengthOptional Blower Fan Installation Secondary InstallationComplete Log Placement Log Placement with Rock Wool Brick panel bracket, slots shown Problem Possible Cause Solution Trouble ShootingReference Part Description Part Number Parts List CastEGWP-505PG EGWP-501PG Parts Diagram Cast Parts List Components Parts List Components Parts Diagram Components To the Dealer WarrantyWarranty Installation Data Sheet

50-1033 specifications

The Enviro 50-1033 is an innovative, environmentally-friendly vehicle designed to meet the growing demand for sustainable transportation solutions. As a part of the advanced Enviro series, the 50-1033 stands out due to its blend of efficiency, performance, and eco-conscious features.

One of the defining characteristics of the Enviro 50-1033 is its low-emission engine technology. The vehicle is equipped with a state-of-the-art diesel engine that adheres to stringent emission standards, significantly reducing pollutants compared to traditional models. This feature not only lessens the environmental footprint but also contributes to improved air quality in urban settings.

Additionally, the Enviro 50-1033 incorporates advanced fuel efficiency technologies, making it an economical choice for fleet operators. With a focus on maximizing fuel economy without compromising performance, this vehicle is designed to deliver cost savings over its lifecycle. The engine employs a combination of turbocharging and high-pressure fuel injection systems, which enhances combustion efficiency and maximizes power output while minimizing fuel consumption.

The vehicle’s design is another noteworthy aspect. Built with lightweight materials and aerodynamics that reduce drag, the Enviro 50-1033 enhances overall performance and maneuverability. The spacious interior is designed to accommodate a larger number of passengers without sacrificing comfort. Ergonomically designed seating and high-quality materials create an inviting atmosphere for both drivers and passengers.

Safety features are a top priority in the Enviro 50-1033. The vehicle is equipped with advanced driver assistance systems, including anti-lock braking systems, traction control, and electronic stability control. These technologies work together to enhance vehicle safety, providing peace of mind for operators and passengers alike.

The Enviro 50-1033 also offers modular design options, allowing customization to meet the specific needs of various transportation services. Whether for public transport, private hire, or shuttle services, the flexibility of the Enviro 50-1033 ensures that it can adapt to diverse operational demands.

In conclusion, the Enviro 50-1033 is a remarkable vehicle that embodies the future of sustainable transportation. With its cutting-edge technologies, eco-friendly features, and commitment to safety and comfort, it represents a significant step forward in the quest for greener urban mobility solutions. As cities globally embrace the transition to cleaner transportation options, the Enviro 50-1033 is well-positioned to play a vital role in shaping the future of public transport.
Top Page Image Contents