Maintenance And Service

ROUTINE MAINTENANCE:

At least once a year, run through the following procedures to ensure the system is clean and working properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything. The pilot flame should be blue with little or no yellow on the tips.

Warning: Clearances must be sufficient to allow access for maintenance and service

Warning: Failure to position the parts in accordance with this manual, or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

The venting system must be periodically examined; it is recommended the examination is done by a qualified agency.

CLEANING THE GLASS:

When the fireplace has cooled, remove the face of the fireplace along with the glass. See MAINTENANCE AND SERVICE - GLASS DOOR REMOVAL. Check the gasket material on the back of the glass, making sure that it is attached and intact.

During a cold start up, condensation will sometimes form on the glass. This is a normal condition with all fireplaces. However, this condensation can allow dust and lint to cling to the glass surface. Initial paint curing of the appliance can leave a slight film behind the glass, a temporary problem. The glass will need cleaning about two weeks after installation. Use a mild glass cleaner and a soft cloth; abrasive cleaners will damage the glass and plated surfaces. Depending on the amount of use, the glass should require cleaning no more than two or three times a season. Do not clean the glass when it is hot.

CLEANING THE FIREBOX:

Remove the logs carefully, as they are very fragile. Gently remove all the embers and rock wool and place on a paper towel. Vacuum the bottom of the firebox thoroughly. Carefully clean any dust off the logs and remove any lint from the burner and pilot. At this time, inspect the burner pan for cracking or severe warping. If a problem is suspected, contact the dealer. Check the logs for deterioration or large amounts of soot; a small amount on the bottom side of the logs is normal. Replace the logs and embers as in the LOG SET AND EMBER INSTALLATION section. If new/more embers and rock wool are required, contact your nearest ENVIRO dealer.

CHANGE BATTERY IN IGNITION MODULE:

If the unit does not spark when lighting, the battery in the electronic ignition could need replacing.

Located on the left hand rear corner of the unit is a small rectangular hole. Located here is the electronic ignition module (see Figure 5). Remove the battery cover, located on the left side of the module, and replace the AA battery.

Reinstall the battery cover and check for spark by depressing the pilot knob located on the control panel.

Electronic

ignition module

Figure 5: Electronic Ignition Module

Location.

50-1033 specifications

The Enviro 50-1033 is an innovative, environmentally-friendly vehicle designed to meet the growing demand for sustainable transportation solutions. As a part of the advanced Enviro series, the 50-1033 stands out due to its blend of efficiency, performance, and eco-conscious features.

One of the defining characteristics of the Enviro 50-1033 is its low-emission engine technology. The vehicle is equipped with a state-of-the-art diesel engine that adheres to stringent emission standards, significantly reducing pollutants compared to traditional models. This feature not only lessens the environmental footprint but also contributes to improved air quality in urban settings.

Additionally, the Enviro 50-1033 incorporates advanced fuel efficiency technologies, making it an economical choice for fleet operators. With a focus on maximizing fuel economy without compromising performance, this vehicle is designed to deliver cost savings over its lifecycle. The engine employs a combination of turbocharging and high-pressure fuel injection systems, which enhances combustion efficiency and maximizes power output while minimizing fuel consumption.

The vehicle’s design is another noteworthy aspect. Built with lightweight materials and aerodynamics that reduce drag, the Enviro 50-1033 enhances overall performance and maneuverability. The spacious interior is designed to accommodate a larger number of passengers without sacrificing comfort. Ergonomically designed seating and high-quality materials create an inviting atmosphere for both drivers and passengers.

Safety features are a top priority in the Enviro 50-1033. The vehicle is equipped with advanced driver assistance systems, including anti-lock braking systems, traction control, and electronic stability control. These technologies work together to enhance vehicle safety, providing peace of mind for operators and passengers alike.

The Enviro 50-1033 also offers modular design options, allowing customization to meet the specific needs of various transportation services. Whether for public transport, private hire, or shuttle services, the flexibility of the Enviro 50-1033 ensures that it can adapt to diverse operational demands.

In conclusion, the Enviro 50-1033 is a remarkable vehicle that embodies the future of sustainable transportation. With its cutting-edge technologies, eco-friendly features, and commitment to safety and comfort, it represents a significant step forward in the quest for greener urban mobility solutions. As cities globally embrace the transition to cleaner transportation options, the Enviro 50-1033 is well-positioned to play a vital role in shaping the future of public transport.