Enviro C-11288 owner manual Removing valve Screw

Page 11
Figure 11: O-ring on valve screw.

Maintenance And Service

7.Convert the SIT gas valve:

a)Remove the black protection cap from the HI/LO knob by hand shown in Figure 8.

b)Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 9), rotate it counter-clockwise until it is free and extract it.

c)Check that the screw is clean and if necessary remove dirt.

d)Flip the screw (refer to Figure 10).

e)Using the Allen wrench as shown in Figure 9, rotate the screw clockwise until a torque of 9 inch lbs. WARNING! Do not over tighten the screw. It is recommended that you grip the wrench by the short side.

Figure 9: Removing valve

screw.

f)Verify that if the conversion is from NG to LPG, the screw must be re-assembled with the red o- ring visible (refer to Figure 11). If the conversion is from LPG to NG, the red o-ring of the screw must be not visible.

Figure 10: Flip valve

screw.

g)Re-attach the black protection cap that was removed in step a (Figure 8).

8.Reinstall the burner, brick panels, log set, embers, and glass door. Also

refer to SECONDARY INSTALLATION - INSTALLING LOG SET AND EMBERS. When

re-installing the burner, ensure that the burner to pilot hood relationship

is similar to what is shown in Figure 12. On some units you will need to pay special attention when installing the burner that the venturi adjustment rod is properly installed into the venturi adjustment piece welded to the burner venturi tube

9.Reconnect the main gas line if it was disconnected and open the shut-off valve at the gas line to the unit.

10.Use a small brush to apply a warm soapy water solution to all gas connections (use a half dish soap and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by using an approved pipe thread sealant or approved Teflon tape. NEVER USE AN OPEN FLAME WHEN TESTING FOR LEAKS.

11.Reconnect the electrical power to the unit.

Figure 12: Burner to pilot hood

relationship.

12.Relight the main burner in both the “HI” and “LO” positions to verify proper burner ignition and operation and proper flame appearance. Also refer to SECONDARY INSTALLATION - LOG SET AND EMBERS INSTALLATION for a flame appearance picture.

13.MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit has been converted to a different fuel type.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Focus General Safety PrecautionsTable of Contents This Enviro Focus Fireplace Codes And ApprovalsDimensions SpecificationsOperating Instructions For Your Safety Read Before OperatingComponent Sound & Reason Natural Gas Propane Venturi Setting RearTop bolts for glass door Maintenance And ServiceEnsuring that wires and gas lines are Way, and snap into place Kit Parts ListConversion Kit Installation Removing valve Screw Minimum fireplace size Width 34 86.36 cm Height 21 53.3 cm Initial InstallationQualified Installers only Installation of Leveling Legs Option 2 Standard Surround Panel Surround Panel installationConverting To a BV Fireplace Parts required for conversionVenting Fireplace Inserts Electrical Requirements To Test Valve Pressures Gas Line ConnectionFocus burner Secondary InstallationBrick Panel Installation Problem Possible Cause Solution Trouble ShootingReference Number Part Description Part Number Parts List ComponentsParts List Components Body Reference Number Part Description Part Number Parts List Surrounds & FasciaParts Diagram Surrounds & Fascia Parts List Cast Parts List Cast Parts Diagram- Cast Bay Front To the Dealer WarrantyWarranty Warranty Installation Data Sheet

C-11288 specifications

Enviro C-11288 is an innovative product that has garnered attention in the environmental technology sector. Primarily designed for sustainability initiatives, this advanced solution integrates a range of features and technologies that address the pressing concerns of waste management and resource conservation.

One of the standout features of Enviro C-11288 is its efficient waste processing capability. Utilizing state-of-the-art waste conversion technologies, it can transform organic and inorganic materials into reusable resources, effectively minimizing landfill use. The incorporation of advanced sorting algorithms ensures that the separation of recyclable materials is efficient and precise, enhancing the overall recycling process.

In addition to waste processing, the Enviro C-11288 is equipped with energy recovery systems. These systems capture and convert waste heat generated during processing into usable energy. This not only energy-optimizes the operation but also contributes to a lower carbon footprint, making it an environmentally friendly solution.

Another significant characteristic of the Enviro C-11288 is its scalability. Whether in a small community or a large industrial setup, the unit can be adapted to meet varying demands. This flexibility is further enhanced by modular design features, allowing users to expand or contract the system as needed without significant interruptions to their operations.

The technology behind Enviro C-11288 is also notable. Real-time monitoring and analytics capabilities enable users to track efficiency metrics, waste reduction rates, and energy consumption. This data-driven approach empowers organizations to make informed decisions about resource management and further improvements.

Durability and low maintenance are additional advantages provided by Enviro C-11288. Constructed with high-quality materials, the system is designed for longevity and can withstand harsh operational conditions. Low maintenance requirements translate into cost savings over time, further appealing to organizations with budget constraints.

Overall, Enviro C-11288 represents a significant advancement in environmental technology solutions. Its combination of waste management efficiency, energy recovery, scalability, real-time monitoring, and durable design positions it as a vital tool for organizations striving to implement sustainable practices while optimizing resource use. As industries continue to emphasize sustainability, the Enviro C-11288 offers a comprehensive solution that aligns with this critical goal.
Top Page Image Contents