Avalon Stoves DVS Insert EF II owner manual Fine Tuning the EMBER-FYRE Burner

Page 26

26

Finalizing the Installation

FINE TUNING THE EMBER-FYRE™ BURNER

Each installation is affected by altitude, vent configuration, and fuel quality. Because of this, the restrictor and air shutter may need to be fine tuned to each installation. Follow the hints below to fine- tune the burner for optimum performance and aesthetics.

Restrictor Adjustment:

Only those installations determined to be over-drafting require this adjustment. See the instructions on page 15 for details.

Air Shutter Hints:

For more glow, open the air shutter, however, this will make the flames more blue.

For yellow flames, close the air shutter, however, this may create less glow.

Correct

Lifting Flames

Ghosting Flames

Flickering Flames

 

Burner Ports

 

 

Burner

(holes)

 

 

The flames should burn right off the top of the burner ports (if they are too blue, adjust the air control).

Lifting flames indicate insufficient draft (restrictor is set too high).

Ghosting flames indicate

Flickering, short flames

insufficient air (restrictor set too

indicate excessive draft

high, air shutter shut down, or

(move air shutter to a higher

other venting error).

position).

Warning: If the vent configuration is installed incorrectly the vent may cause the flames inside the heater to lift or “ghost” – a dangerous situation. Inspect the flames after installation to insure proper performance. If the vent configuration is correct, yet the flames are lifting or ghosting, shut off gas to the heater and contact the dealer for information on remedying the problem.

8.Replace the glass.

9.Attach the face following the directions included with the face.

NOTE: If using a Rosario or Discovery face you may wish to modify the face connector (see page 11 for details).

NOTE: If using the Arched, Artisan, Metropolitan, or Victorian Lace Face you must use the face mounting brackets included with the heater (see page 12 for details).

10.Turn the flame adjust knob to its highest position - the flames should not contact the top of the firebox. Check the flame on low position. The flames should burn off of each burner hole. If the heater does not work correctly, contact your dealer for a remedy.

11.Give this manual to the home owner and fully explain the operation of this heater.

© Travis Industries

4060111

100-01175

Image 26
Contents DVS Insert EF Travis Industries, IncSave Your Bill of Sale 2IntroductionIntroduction Important Information 4060111Table of Contents Safety Precautions If YOU Smell GASDo not place anything inside Dimensions Features Installation OptionsHeating Specifications Natural Gas PropaneInstallation for qualified installers only Top Convection Deflector Fireplace RequirementsFactory-Built Metal Wood-Burning Fireplace Requirements Hearth RequirementsLeveling Bolts Clearances Mantel ClearancesRequires the Bedford DVS EF II Face Upgrade Kit Face SizingMounting the Bedford Face Gas Inlet Pressure Gas Line RequirementsGas Line Location Vent Requirements Altitude ConsiderationsVent Installation Vent RestrictorVent Configurations Vent LocationVent Connector Removal and Installation Vent Connector Removal Surround Panel Installation Electrical Connection Installation Without Surround PanelsInstallation of the On/Off Switch and Rheostat Finalizing the Installation Glass Frame Removal and InstallationFinalizing the Installation Log Set Installation Finalizing the Installation Pilot Flame Inspection Steps for Finalizing the InstallationAir Shutter Adjustment Fine Tuning the EMBER-FYRE Burner Location of Controls Operation27Before You Begin Seconds once it is lit 28OperationStarting The Pilot Flame Starting the Heater for the First Time Adjusting the Flame HeightOperation29 Turning the Heater On and OffNormal Operating Sounds Adjusting the Blower Speed30Operation Normal Operating OdorsMaintaining Your Heaters Appearance Maintenance31Yearly Service Procedure 32Maintenance Troubleshooting TableWhat Turns the Main Burners On and Off Maintenance33How this Heater Works What Prevents Gas BuildupReplacement Parts List 34MaintenanceWiring Diagram Safety Label Safety LabelYears 3 Through 5 Coverage Parts & Labor Limted 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyOptional Equipment for qualified installers only LP Conversion InstructionsOptional Equipment for qualified installers only To adjust the pilot flame, turn this screw Note if totally Firebacks Lower Surround Panel Index

DVS Insert EF II specifications

The Avalon Stoves DVS Insert EF II is a sophisticated heating solution designed to bring warmth and comfort to modern homes while enhancing their aesthetic appeal. This impressive insert is characterized by its advanced engineering and striking design, making it a perfect addition to any living space.

One of the primary features of the Avalon DVS Insert EF II is its efficient heating capability. With a heating capacity of up to 2,200 square feet, it is ideal for larger rooms or open concept areas. Utilizing a powerful EPA-certified wood-burning system, the insert delivers a clean and efficient burn, ensuring that you maximize heat while minimizing emissions. This feature aligns with the growing demand for environmentally friendly heating options and complies with strict emissions standards.

The design of the DVS Insert EF II is marked by a large, stylish viewing area that provides an unobstructed view of the flames, creating a beautiful focal point in any room. This model is equipped with a durable glass door that not only showcases the fire but also contributes to the overall energy efficiency by maintaining optimal heat levels within the insert. The clean lines and sophisticated finish of the insert further enhance its visual appeal, making it suitable for both contemporary and traditional interiors.

In addition to its aesthetic charm, the Avalon DVS Insert EF II incorporates advanced technologies that improve user experience and functionality. The built-in temperature control system allows users to adjust the heat output with ease, ensuring a comfortable environment at all times. Furthermore, the unit features an easy-to-use ash pan and a self-cleaning glass mechanism that simplifies maintenance, allowing homeowners to enjoy their fireplace without the hassle of frequent cleaning.

The construction of the DVS Insert EF II emphasizes durability and longevity. Made from high-quality materials, this insert is designed to withstand the rigors of daily use while providing years of efficient heating. The heat exchanger technology maximizes heat output while minimizing the consumption of fuel, making it an economical choice for homeowners.

Overall, the Avalon Stoves DVS Insert EF II is a compelling choice for those seeking a powerful, efficient, and aesthetically pleasing heating solution. Its combination of innovative technologies, user-friendly features, and elegant design positions it as a top contender in the wood stove market, providing both comfort and style for any home. Whether you are looking to replace an old insert or add a new feature to your living space, the Avalon DVS Insert EF II stands out as an exemplary option.