LEG Option on H2100 Hearth Heater | Regency I3100L specs

INSTALLATION

LEG OPTION ON H2100

HEARTH HEATER

The addition of legs to the Hearth Heater does not alter its certiﬁcation, it does not become a freestanding woodstove. The H2100 can only be installed as a Hearth Heater i.e. vented into a masonry or factory built ﬁreplace.

The instructions below apply to the steel leg, painted cast leg and the gold plated cast leg. It will be easier to attach the legs to the stove if it is tipped on its back (preferably on a soft surface to prevent scratching).

1)Thread the bolt and washer through the leg, and then into the nutsert in the base of the stove and tighten.

2)Level the stove by adjusting the levelling bolts in the bottom of each leg.

NOTE: Adding the legs changes the height of the unit, make sure you have sufficient clearance (min. 28") for your ﬂue connection.

FLUE CONNECTOR

BRACKET

Package contains: 3 brackets and 6 screws.

These brackets are to be used to hold the ﬂue liner (not supplied) to the Insert and keep the connection. The brackets are screwed into the top of the Insert in the pre-punched holes and then screwed into the ﬂue liner.

INSTALLATION INTO A MASONRY FIREPLACE

When referencing installation or connec- tion to masonry ﬁreplaces or chimneys, the masonry construction must or shall be code complying.

The insert must be installed as per the require- ments of your local inspection authority. Three methods of ﬂue connection are acceptable in most areas, these include:

1)Positive ﬂue connection, where a large blocking plate and a short connector pipe is used.

2)Direct ﬂue connection, where a smaller blocking plate and a connector pipe to the ﬁrst ﬂue liner tile is used.

3)Full ﬂue liner, where a stainless steel rigid or ﬂexible liner pipe is routed from the insert outlet collar to the top of the chimney.

Regency highly recommends the use of a full liner as the safest installation and provides the most optimum performance. Your retailer should be able to help you decide which system would be the best for your application.

1) Positive Flue

2) Direct Flue

Connection

with Cleanout

In Canada this ﬁreplace insert must be in- stalled with a continuous chimney liner of 6" diameter extending from the ﬁreplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirements of CAN/ULC-S640, Standard for Lining Sys- tems for New Masonry Chimneys.

Note: A clean-out door is sometimes required, by your inspector, to be installed when either the Positive ﬂue connection or Direct ﬂue connection method is used.

The use of one of the connection methods listed on this page not only increases the safety of your insert by directing the hot gases up the ﬂue, but will also help increase the unit's efﬁciency and decrease creosote deposits in the chimney.

When a connected ﬂue or liner is in use, the insert is able to “breathe” better by allowing a greater draft to be created. The greater draft can decrease problems such as, difﬁcult start-ups, smoking out the door, and dirty glass.

INSTALLATION INTO A

FACTORY BUILT

FIREPLACE

1)When installed in a factory built ﬁreplace, a full stainless steel rigid or ﬂexible ﬂue liner is mandatory, for both safety and perform- ance purposes. When a ﬂue or liner is in use, the insert is able to breathe better by allowing a greater draft to be created. The greater draft can decrease problems such as, difﬁcult start-ups, smoking out the door, and dirty glass.

2)In order to position the ﬂue liner, the exist- ing rain cap must be removed from your chimney system. In most cases the ﬂue damper should also be removed to allow passage of the liner.

3)In most cases opening the existing spark screens fully should give enough room for the insert installation. If it does not, remove and store.

3a) Full Flue Liner	3b) Hearth Heater with
(No Cleanout	Full Flue Liner
Required)	(No Cleanout
	Required)

8	Regency Wood Insert & Hearth Heater

H2100, I3100L specifications

The Regency H2100 and I3100L are two innovative and efficient heating solutions that cater to the evolving needs of modern homes. Known for their quality craftsmanship and advanced technology, these products have become favorable choices among homeowners seeking both aesthetics and functionality.

The Regency H2100 is a gas fireplace insert designed specifically to be installed within an existing fireplace. It features a sleek and contemporary design that enhances the ambiance of any room while providing effective heating. One of the main highlights of the H2100 model is its high efficiency rating, often exceeding 70%. This efficiency translates to reduced energy costs and a minimal environmental footprint. Equipped with a powerful heating capacity, the H2100 can effectively warm spaces up to 1,500 square feet, ensuring comfort during the coldest months.

Key technologies integrated into the H2100 include a direct vent system that allows for safe and efficient exhaust of combustion gases, promoting clean indoor air quality. Additionally, the unit features adjustable flame settings and an easy-to-use remote control, allowing for customized heating options to meet individual preferences. The H2100 also includes a variety of aesthetic options, such as different media choices, decorative surrounds, and glass doors, making it suitable for diverse interior designs.

On the other hand, the Regency I3100L is a wood-burning insert designed for homeowners who appreciate traditional heating methods. This model boasts a large firebox that can accommodate larger logs, providing extended burn times and minimal need for refueling. With an impressive efficiency rating, the I3100L minimizes wood consumption while maximizing heat output.

One of the standout characteristics of the I3100L is its large viewing glass, offering an unobstructed view of the fire, creating an inviting atmosphere. The insert features secondary combustion technology, which ensures that smoke and emissions are significantly reduced, promoting environmental friendliness. With its classic cast iron construction, durability is another crucial feature, ensuring that the insert will withstand the test of time while providing consistent warmth.

In conclusion, both the Regency H2100 and I3100L present unique heating solutions tailored to different preferences and lifestyles. With their advanced features, energy efficiency, and customizable designs, these models stand out in the market, offering homeowners the perfect blend of comfort, style, and sustainability in their heating solutions. Whether one prefers the convenience of gas or the charm of wood-burning, Regency has positioned itself as a leader in innovative heating technology.