Regency Inserts are constructed with the high- est quality materials and assembled under strict quality control procedures that insure years of trouble free and reliable performance.
It is important that you read this manual thor- oughly and fully understand the safe instal- lation and operating procedures. The more you understand the way your Regency Insert operates, the more enjoyment you will experi- ence from knowing that your unit is operating at peak performance.
BEFORE INSTALLING
YOUR INSERT
1)Read all instructions before installing and using your fireplace insert. Install and use only in accordance with manufacturer’s installation and operating instructions.
2)Check your local building codes - Building Inspection Department. You may require a permit before installing your insert. Be aware that local codes and regulations may override some items in the manual.
WARNING: Careless installation is the major cause of safety hazard. Check all local building and safety codes before installation of unit.
3)Notify your home insurance company that you plan to install a fireplace insert or hearth heater.
4)Your fireplace insert is heavy and requires two or more people to move it safely. The insert can be badly damaged by mishan- dling.
5)If your existing fireplace damper control will become inaccessible once you have installed your Regency Insert, you should either remove or secure it in the open posi- tion.
6)Inspect your fireplace and chimney prior to installing your insert to determine that it is free from cracks, loose mortar or other signs of damage. If repairs are required, they should be completed before installing your insert. Do not remove bricks or mortar from your masonry fireplace.
7)Do not connect the insert to a chimney system servicing another appliance or an air distribution duct.
Emissions from burning wood or gas could contain chemicals known to the State of Cali- fornia to cause cancer, birth defects or other reproductive harm.
CHIMNEY
SPECIFICATIONS
Before installing, check and clean your chimney system thoroughly. If in doubt about its condi- tion, seek professional advice. Your Regency Insert is designed for installation into a masonry fireplace that is constructed in accordance with the requirements of "The Standard for Chimneys, Fireplaces, Vents, and Solid Fuel Burning Ap- pliance", N.F.P.A. 211, the National Building Code of Canada, or the applicable local code requirements.
The appliance, when installed, must be electri- cally grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code,ANSI/NFPA70, or the Canadian Electrical code, CSA C22.1.
Regency Inserts are designed with a 6" (152mm) flue.
Requirements for Installing
Solid-fuel Inserts in Factory-built
Fireplaces.
1)The insert must be tested and meet the requirements of UL 1482 (U.S.) and or ULC S628 (Canada) when tested in a masonry fireplace built per ULC S628.
2)The factory-built fireplace must be listed per UL 127 or ULC S610.
3)Clearances obtained from the masonry fire- place tests are also relevant for installation in factory-built fireplaces.
4)Installation must include a full height listed chimney liner type HT requirements (2100 degree F.) per UL 1777 (U.S.) or ULC S635 (Canada). The liner must be securely attached to the insert flue collar and the chimney top.
5)Means must be provided to prevent room air passage to the chimney cavity of the fireplace. This may be accomplished by sealing the damper area around the chimney liner, or sealing the fireplace front.
6)Alteration of the fireplace in any manner is not permitted with the following exceptions;
a.external trim pieces which do not affect the operation of the fireplace may be removed providing they can be stored on or within the fireplace for re-assembly if the insert is removed.
b.the chimney damper may be removed to install the chimney liner.
7)Circulating air chambers (i.e. in a steel fireplace liner or metal heat circulator) shall not be blocked.
8)Means must be provided for removal of the insert to clean the chimney flue.
9)Inserts that project in front of the fireplace must be supplied with appropriate supporting means.
10)Installer must mechanically attach the sup- plied label to the inside of the firebox of the fireplace into which the insert is installed.
"WARNING: This fireplace has been converted for use with a wood insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fireplace re-approved by the authority having jurisdiction."
In order for a solid-fuel insert to be certified for use in factory-built fireplaces, the above information must be clearly stated in the instal- lation manual and appropriate markings. Final approval is contingent on the authority having jurisdiction.
FIREPLACE
SPECIFICATIONS
Your fireplace opening requires the following minimum sizes:
| Height | Width Depth |
Large (I3100L) | 25" | 28" | 17" |
Hearth Heater (H2100M) | 20.0" | -- -- |
Two faceplates are available to seal the fire- place opening:
Standard | Oversize |
Large (I3100L) | |
44"W x 32"H | 50"W x 34.5"H |
Hearth Heater (H2100M) | |
40 1/4"W x 30"H | 48"W x 33"H |
INSTALLING YOUR
INSERT
Your insert is very heavy and will require two or three people to move it into position. The insert can be made a little lighter by removing the cast iron door by opening it and lifting it off its hinges. Be sure to protect your hearth extension with a heavy blanket or carpet scrap during the installation.
Convection Grills for
I3100L
The convection grills are installed before the unit is positioned inside the fireplace.
