Regency E33S installation manual GAS Connection, Venting, Flue Liner Installation

Page 10

INSTALLATION

INSTALLATION

GAS CONNECTION

GAS CONNECTION WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance.

1)If the appliance is to be installed into an existing chimney system, thoroughly clean the masonry or factory built fireplace.

2)The appliance is provided with an opening on the left hand side of the control compartment. A 3/8" NPT gas supply pipe must be brought near this inlet hole.

3)Locate the center point where the vent will pass through the chimney above the appliance. Move the appliance into the exact location where it is to be installed. Ensure that the Insert is level.

NOTE: This unit is equipped with a heat sensor thermodisc which will prevent the blower from operating until the unit reaches the correct temperature.

VENTING

THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE.

This appliance is designed to be attached to two 3" (76mm) co-linear aluminium flex running the full length of the chimney. The flue length must be a minimum length of 8 ' (2.44m) and a maximum of 35' (10.7m). See chart above for minimum distances from roof. Periodically check that the vent is unrestricted.

Masonry chimneys may take various contours which the flexible liner will accommodate. However, keep the flexible liner as straight as possible, avoid unnecessary bending.

Part #

Description

948-305

3" Flex - 35 ft.

946-529

FPI Co-linear DV Vertical

 

Termination Cap

Alternate Approved Caps

46DVA-VC

 

Vertical Termination Cap

 

46DVA-VCH

 

High Wind Cap

 

46DVA-GK

 

3" Co-linear Adaptor with

 

 

 

 

 

flashing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In areas of consistently high winds, we recommend using the Simpson Dura-Vent System (46DVA-GK adapter and 46DVA-VCH high-wind cap).

The Air Intake pipe must be attached to the inlet air collar of the termination cap.

FLUE LINER

INSTALLATION

1)Cut the flex liner as required.

2)Mark the end of one liner with an "E" to indicate Exhaust.

3)Connect the other end of the above liner to the exhaust side of the termination adaptor, seal connection with high temperature silicone. Secure with gear clamp.

4)Connect the 2nd liner to the inlet side of the adaptor, seal connection with high temperature silicone. Secure with gear clamp.

5)Install flashing.

6)Insert both liners into chimney, passing through the damper opening.

7)Install termination cap.

8)Connect the marked end of the liner to the exhaust collar of the vent connector plate marked with an "E", seal connection with high temperature silicone. Secure with gear clamp.

9)Connect the 2nd liner to the intake collar, seal connection with high temperature silicone. Secure with gear clamp.

10)Align vent connector plate with guides on unit.

11)Slide unit into masonry opening, while ensuring that the slot at the rear of the connector plate mates up with the hold down plate on the unit.

12)Secure with Screw.

NOTE:

1)Final gas connection should be made after unit is in place to avoid damage to line when pushing the unit into position.

2)Mill-pac may be used instead of high tempture silicone and screws may be used instead of gear clamps at connections of liner to inlet and vent collars.

10

Regency® E33S-1 Sunrise Gas Insert

Page 9 Page 11
Image 10
Page 9 Page 11
Contents E33 Sunrise Gas Insert FPI GAS Fireplace Insert Table of Contents Safety Label Requirements MA Code CO DetectorUnit Dimensions Installation Minimum Fireplace Opening Installation ChecklistMaterials Required Minimum Clearances to Combustibles GAS Connection Flue Liner InstallationVenting GAS Pipe Pressure Testing GAS Insert Aeration SystemConversion KIT #434-969FROM NG to LP Installation Installation Any hot surfaces Wiring DiagramsWires do not touch Are away from sharpThermostat Wire Table Optional Wall ThermostatGlass Crystal or Optional Ceramic Stones Installation Glass Door InstallationContemporary Faceplate Door Frame Installation Kit# 341-914 Contents ListCompleted Faceplate & Door Frame Installation Optional Hearth Trim Installation Hearth Trim 341-942 InstallationOperating Instructions Automatic Convection FAN Operation Copy of Lighting Instruction PlateNormal Operating Sounds GAS Appliances General Vent Maintenance MaintenanceMaintenance Instructions Glass ReplacementValve Tray Replacement Door FrameBase Cover FAN Replacement Maintenance Parts List Main AssemblyContemporary Faceplate & Door Frame Regency E33S-1 Sunrise Gas Insert Warranty ConditionsInstaller Please complete the following information

E33S specifications

The Regency E33S is a remarkable venture into the realm of compact, feature-rich functional appliances, specifically engineered to cater to a variety of user needs. Designed with elegance and functionality in mind, the E33S stands out due to its modern aesthetic and advanced technology.

One of the main features of the Regency E33S is its powerful energy-efficient system, which ensures optimal performance while minimizing electricity consumption. This appliance is equipped with a high-efficiency compressor that not only reduces energy costs but also maintains a consistent temperature, contributing to the longevity of the items stored within.

In terms of capacity, the E33S boasts ample storage space, making it an excellent choice for both residential and commercial users. With intelligently designed shelving arrangements, it allows for the maximum utilization of space, accommodating various sizes and types of items. The adjustable shelves provide flexibility, which is essential for diverse storage needs.

The E33S is also integrated with innovative smart technology. Featuring Wi-Fi connectivity, users can monitor and control the appliance remotely, ensuring optimal performance and peace of mind. The accompanying mobile application allows for temperature adjustments, alerts for any fluctuations, and energy usage tracking, making it a highly user-friendly solution.

In addition, the Regency E33S prioritizes hygiene and freshness. It is equipped with advanced filtration systems that minimize odors and effectively filter out contaminants. This feature is particularly beneficial for preserving food quality and extending shelf life.

Another notable aspect of the E33S is its sleek design, which fits seamlessly into any decor. The appliance is available in various finishes, allowing users to choose one that complements their space beautifully. The exterior is not only stylish but also durable, ensuring longevity.

Lastly, built with eco-friendly materials, the Regency E33S reflects a commitment to sustainability. Its construction takes into account environmental impact, making it an ideal choice for eco-conscious consumers.

In conclusion, the Regency E33S combines efficiency, innovative technology, and elegant design to meet the diverse needs of modern users, setting a new standard in the compact appliance market.
Top Page Image Contents