Monte Carlo Fan Company 5VYR56XXD Installation, Before you begin installing the fan, Switch

Installation

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

1. Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including fire-rated construction.

2. Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.

3. After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con- ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

4. Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

5. Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

7. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.

8. WARNING – Risk of fire, electric shock, or personal injury. The fan in this box may be either directly supported from a structural fram- ing member of a building and/or may be mounted to an outlet box marked acceptable for fan support of 31.8 kg. (70 lbs.) or less. Most outlet boxes commonly used for the support of luminaires may not be acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

9. Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

10. Attach the mounting bracket using only the hardware supplied with the outlet box.

11. To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

12. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

13. NEVER place a switch where it can be reached from a tub or shower.

14. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat- ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

15. Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1	Phillips Screwdriver		Wire Cutters		Pliers
		2		OUTLET BOX METHOD

	Before you begin installing the fan, Switch		Warning-Risk of			fire, electric shock, or personal
			injury. The fan in this box may be either directly sup-
	power off at Service panel and lock service dis-		ported from a structural framing member of a build-
	connecting means to prevent power from being		ing and/or may be mounted to an outlet box marked
	switched on accidentally. When the service dis-		acceptable for fan support of 31.8 kg(70lbs) or less.
	connecting means cannot be locked, securely		Most outlet boxes commonly used for the support of
	fasten a prominent warning device, such as a		luminaires may not be acceptable for fan support and
			may need to be replaced. Consult a qualified electri-
	tag, to the service panel.		cian if in doubt.
4		5			BUILDING STRUCTURE METHOD
							Mounting
				Outlet box			Plate
					Wood
					Screws
	Remove the 4 screws attaching the Mounting	Secure mounting plate directly to a joist from
	neck to the mounting plate. Retain the 4	the buliding structure via the two knock out
		holes on the outlet box. Use only the appropri-
	screws for re-assembly.	ate wood screws and washers included with
		your fan. Caution: Wood screws must go
		through into the building joist.

Step Ladder

3

Remove Safety bar from mounting bracket by loosing screws, sliding bar to side, and lifting it off the 2 screws.

6 FAN BRACE AND BOX METHOD

Install the mounting Plate to approved fan brace and box combination use only the hard- ware provided with the fan brace and box.