Phillips Screwdriver

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

1.Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999), including fire-rated construction.

2.Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

3.After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con- ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

4.Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

5.Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

6.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

7.Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.

8.To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)

9.Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

10.Attach the mounting bracket using only the hardware supplied with the outlet box.

11.To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

12.The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat- ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

13.Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

14.Airflowdirection: warm weather-switch to left - forward / cool weather -switch to right - reverse

	Phillips Screwdriver	TOOLS REQUIRED	Pliers		Step Ladder
	Phillips Screwdriver	Wire Cutters	Pliers	3	Step Ladder
1	2			3

Use metal outlet box suitable for fan support

and use only the screws provided with the out-

let box (must support 35 lbs). Before attach-

Before you begin installing the fan, Switch

ing fan to outlet box, ensure the outlet box is

power off at Service panel and lock service dis-

Before installing this fan make sure the outlet box is

securely fastened by at least two points to a

connecting means to prevent power from being

properly installed to the house structure. To reduce

switched on accidentally. When the service dis-

the risk of fire, electric shock, or personal injury,

structural ceiling member ( a loose box will

connecting means cannot be locked, securely

mount to outlet box or supporting system acceptable

cause the fan to wobble). Use only the

fasten a prominent warning device, such as a

for fan support. (Mounting must support at least 35

screws provided with the outlet box.

tag, to the service panel.

lbs.)

Yoke cover

Canopy

Cross Pin

Keeper

Yoke

Canopy disk

Downrod

Loosen the 2 set screws in yoke for

downrod to slip into yoke. Insert

downrod into yoke on top of the Fan

Tread leadwires and

safety cable first

Body. Align the hole in the Downrod

Tighten the 2 Set screws on the Yoke

through the yoke cover, canopy disk,

with the hole in the Yoke. Insert the

once the downrod is in place. Check

Canopy and last the downrod.

Pin through the Yoke and Downrod

motor for shipping stabilizers and

until the point appears on the other

remove if present.

side. Install the Keeper Pin

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

Pliers

Step Ladder

Wire Cutters