Lifebreath 155MAX RX, 200MAX RX, 155ECM installation manual Motors Maintenance Free

Page 32

Maintenance Routine for ERV (for HRV, see previous page)

1.Inspect Exterior Hoods at least once a month Make sure exhaust and fresh air supply hoods are not blocked up or restricted by leaves, grass, or dirt.

WARNING: Blockage of hoods may cause an imbal- ance.

2. Clean Air Filters Four Times a Year

The standard filters equipped with your ERV are removable and washable.

a)simply open access door and slide core out

b)remove filter clips.

c)once clips are removed filters can be taken off the core to be rinsed with water or a combination of soap and water.

d)to assemble, place clean dry filters back into their positions.

e)install core to its original position

3.Clean Core Twice a Year a) open access door

b)carefully grip ends of core and pull evenly outward. Core may be snug, but will slide out of the channel

c)once removed from the cabinet remove filters

d)vacuum core to remove dust from core surface. DO NOT WASH!!

e)install the clean, dry filters

f)install clean core

NOTE: Core installation label on the outer end of the core.

To install the clean core:

a)first mount the bottom flange of the core guide into the bottom H channel approximately 1/4" (6 mm)

b)mount the left or right side flange of the core guide approximately 1/4" (6 mm) followed by the other side

c)mount the top flange of the core guide into the top H channel approximately 1/4" (6 mm)

d)with all four corners in place and the core straight and even, push hard in the center of the core until the core stops on the back of the cabinet.

NOTE: Core will appear to stick out from cabinet approximately 1/8" (3 mm). This is designed this way so that the access door will fit tight against the core.

5. Clean Duct Work if Required

T he duct work running to and fro m the ERV ma y accumulate dirt. Wipe and vacuum the duct once every year. You may wish to contact a Heating/ Ventilation company to do this.

6. General Maintenance - Twice a Year

Wipe down the inside of the cabinet with a damp cloth to remove dirt, bugs and debris that may be present.

7. Cleaning the Fans

Fans may accumulate dirt causing an imbalance and/or excessive vibration of the ERV. A reduction in the air flow may also occur. In new construction this may result within the first year due to heavy dust and may occur periodically after that over time depending on the outdoor conditions.

•unplug the ERV and open the service door

•remove the core

•remove ducting (metal and/or flexible insulated type) from the red and/or blue ports which are connected immediately inline with the fan assembly

•use a small brush, such as an old toothbrush or pipe cleaner, and insert first

(a)through the large opening of the fan assembly and then

(b)through the smaller opening in the end of the fan assembly.

•scrub individual fan blades until clean. Avoid moving or damaging balancing flat weight, clip is usually found on one or more of the fan blades

•vacuum and wipe

•reassemble making sure ducting is reattached firmly and insulation and moisture barrier are sealed and taped

Before attempting this task, thought should be given to having a qualified service technician complete the service work.

4. Motors - MAINTENANCE FREE

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 155MAX 155ECM 200MAXTable of Contents InstallationMaintenance WarrantyWhere do you use an ERV instead of an HRV? Why transfer moisture in the summer cooling season?So why use an ERV? What is the maintenance?Page Dimensions 95MAX inches mm Model 95MAXDimensions 155MAX inches mm Model 155MAXDimensions 155ECM Performance Model 155ECMDimensions 155MAX RX inches mm Model 155MAX RXDimensions 200MAX inches mm Model 200MAXDimensions 200MAX RX inches mm Model 200MAX RXDimensions Maxtop inches mm Model MaxtopDimensions 195DCS inches mm Model 195DCSDimensions 300DCS inches mm Model 300DCSDimensions 200ERV inches mm Model 200ERVDimensions 200ERVD inches mm Model 200ERVDGlossary Function and Controls Operating the ControlAirSelf Test Automatic Defrost OperationWhich Mode of Operation is Best for Me? Modes of Operation LED Indication20 on / 40 OFF To select speedControl Pad Mounted in the Control Module ControlAirOptional Timers Digital Electronic Timer DETCrank Timer Ventilation DehumidistatUsing the Dehumidistat MAX Port Specifications Round port bent to ovalVariable Port Location MAX Air FlowInstallation Location Connecting Appliances to the HRV/ERVInstalling the Drain Line and P-Trap MountingWarmside Ducting Supply Air Ducting Direct Connection to Furnace DuctworkIndirect Connection to Ductwork Stale Air Exhaust SystemInstallation Diagrams Partially Dedicated SystemSimplified Installation Supply/Return Method Fully Dedicated System Balancing Procedure Pitot Tube Air Flow BalancingBalancing Collar Instructions Hard/Rigid DuctingClean Core Twice a Year a open access door To install the clean coreGeneral Maintenance Twice a Year Cleaning the FansMotors Maintenance Free Symptom Cause Solution Troubleshooting your HRV/ERV SystemWire Residential Wiring Diagram Residential Wiring Diagram For All Models Except 155ECMResidential Wiring Diagram Residential Wiring Diagram 155ECM

200MAX RX, 155MAX RX, 155ECM specifications

Lifebreath 200MAX RX, 155MAX RX, and 155ECM are high-performance heat recovery ventilators designed to enhance indoor air quality while maximizing energy efficiency in residential and commercial spaces. These systems are equipped with advanced technologies that ensure fresh air circulation, reduced energy consumption, and improved overall comfort.

The Lifebreath 200MAX RX is a robust unit that offers a balanced air exchange system, delivering up to 200 CFM (cubic feet per minute) of airflow. This model features a high-efficiency heat exchanger that transfers heat from outgoing stale air to incoming fresh air, significantly reducing energy costs associated with heating and cooling. The unit is designed for larger spaces, making it an ideal choice for homes with open floor plans or commercial environments requiring substantial ventilation.

The 155MAX RX is tailored for medium-sized spaces, providing up to 155 CFM of airflow. It incorporates a similar high-efficiency heat recovery process as the 200MAX RX, ensuring optimal temperature retention without compromising air quality. This unit is equipped with a variable speed motor that allows users to adjust airflow settings according to their specific needs, facilitating better control over indoor climate conditions.

On the other hand, the Lifebreath 155ECM is notable for its energy conservation capabilities, featuring an electronically commutated motor (ECM) that offers superior efficiency and quieter operation. This model is particularly advantageous for those looking to minimize energy consumption while maintaining effective ventilation. The ECM technology allows for precise adjustments to the airflow, adapting to changes in indoor air quality needs seamlessly.

All three models are designed with user-friendly features, including easy-access filters for simple maintenance and cleaning. Their compact design allows for flexible installation in various areas, including attics, basements, or utility closets. Lifebreath products also come equipped with control systems that enable users to monitor and manage air quality more effectively.

In conclusion, the Lifebreath 200MAX RX, 155MAX RX, and 155ECM are exceptional choices for those seeking to improve their indoor air quality while enhancing energy efficiency. With their innovative technologies, capacity for heat recovery, and ease of maintenance, these heat recovery ventilators represent an investment in healthier, more comfortable living spaces.
Top Page Image Contents