SPEEDFIT SYSTEM COMPONENTS
Speedfit Underfloor Heating Products have been designed and are manufactured to European and UK Standards, including ISO 9001 and DIN4726.
MANIFOLDS |
|
|
|
| |
|
| PART | DESCRIPTION | PACK |
|
|
| NO. |
| QTY |
|
|
| JGUFHMAN4 | 4 ZONE MANIFOLD | 1 |
|
|
| JGUFHMAN6 | 6 ZONE MANIFOLD | 1 |
|
|
| JGUFHMAN8 | 8 ZONE MANIFOLD | 1 |
|
|
| JGUFHMAN10 | 10 ZONE MANIFOLD | 1 |
|
|
| JGUFHMAN12 | 12 ZONE MANIFOLD | 1 |
|
|
| Supplied with Speedfit Pipe Inserts and Collet Clips. |
|
| |
Speedfit Manifolds are manufactured from high quality DZR brass to the highest UK and European standards.
A unique feature is that connections to the heating pipes are Speedfit Push Fit, offering much reduced installation time. Flow and return rails are offset and the angles can be altered, all making for an easy installation.
The manifolds are complete with adjustable flow gauge, drain valve and air bleed valve. They are pre assembled on wall brackets and supplied with screws and plugs.
MANIFOLD EXTENSION KIT |
|
| ||
|
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY |
|
| JGUFHMANEXT | MANIFOLD EXTENSION KIT 1 | |
| Enables a manifold to be extended | |||
| by one or more zones. |
| ||
MANIFOLD ELBOW CONNECTOR |
| |||
|
| PART |
| PACK |
|
| NO. |
| QTY |
|
| JGUFHMANELB |
| 1 PAIR |
Enables a Pump Pack and Manifold to be installed at 90º to each other.
PUMP PACK |
|
|
|
|
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY |
|
| JGPUMPPACK | PUMP PACK | 1 |
|
Manufactured in DZR brass, the pack consists of a pump, mixing valve and overheat temperature thermostat.
Hot water is taken from the boiler, mixed to the required temperature and circulated via the manifold to the heating circuits, the temperature and volume of water is constantly altered to maintain the requirements of the system. Flow temperature can be altered by turning the hand wheel on the mixing valve unit.
The pack is light and compact so a wall bracket is not needed and flat face unions make for an easy connection to the manifold.
23
PEX BARRIER PIPE |
|
|
|
|
|
| PART | DESCRIPTION | SIZE | PACK | |
| NO. |
|
| QTY | |
| BARRIER PIPE | 15MM X 50M | 1 |
| |
| BARRIER PIPE | 15MM X 100M | 1 |
| |
| BARRIER PIPE | 15MM X 120M | 1 |
| |
| BARRIER PIPE | 15MM X 150M | 1 |
| |
POLYBUTYLENE BARRIER PIPE |
|
|
| ||
| PART | DESCRIPTION | SIZE | PACK |
|
| NO. |
|
| QTY |
|
| BARRIER PIPE | 15MM X 50M | 1 |
| |
| BARRIER PIPE | 15MM X 100M | 1 |
| |
| BARRIER PIPE | 15MM X 120M | 1 |
| |
| BARRIER PIPE | 15MM X 150M | 1 |
| |
Offered in PEX or Polybutylene, Speedfit Pipe has an inner barrier to prevent the ingress of atmosphere, it is manufactured and Kitemarked to British Standard BS7291 : Parts 1,2 & 3: Class S.
It is lightweight and flexible making it especially suitable for underfloor heating installations.
For screed systems, the pipe is attached directly to insulation with staples, floor clips or mounting rails.
Spreader Plates are available for timber flooring using either traditional joists or TJI Joists.
PIPE FIXING SYSTEMS
Speedfit offer several ways of securing pipe to the insulation layer in a screeded floor.
PART | DESCRIPTION | SIZE | PACK |
NO. |
|
| QTY |
JGUFHSTAPLE | PIPE STAPLES | 60mm | 300 |
JGUFHGUN | STAPLE GUN | - | 1 |
Black Staples are barbed to ensure a secure fixing to the insulation. Easy fixing is carried out by using a Staple Gun, securing pipe to the insulation with an easy repeatable action.
PART | DESCRIPTION | PACK |
NO. |
| QTY |
JGUFHRAIL | 2 METRE LONG | 16 |
JGUFHPIN | RAIL PINS FOR ABOVE | 100 |
Mounting Rails offer a quick installation of 15mm pipe. Supplied 2 metres long, the rails are pre scored every 100mm for easy cutting. The rail can be secured to the insulation using red Rail Pins.
|
|
| PART | DESCRIPTION | PACK |
| ||
|
|
| NO. |
| QTY |
| ||
|
| JGUFHCLIP | FLOOR CLIP | 100 |
|
| ||
|
| JGUFHTOOL FOR EASY FIXING OF FLOOR CLIPS | 1 |
|
| |||
|
|
|
| |||||
| Floor Clips screw easily into insulation, they | |||||||
| are best installed using a Fixing Tool. |
|
|
| ||||
EDGE INSULATION STRIP |
|
|
|
| ||||
|
|
|
| PART | DESCRIPTION | PACK |
|
|
|
|
|
| NO. |
| QTY |
| |
|
|
|
| JGUFHEDGE | 25 METRE ROLL | 1 |
|
|
Supplied in 25 metre rolls, the edge insulation strip is placed round the edge of each room to provide insulation of the heated floor.
FLOOR PANELS |
|
|
|
|
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY |
|
| JGUFHTILE | Floor Tile | 12 |
|
|
| 1400mm x 800mm |
|
|
Supplied in packs of 12, Speedfit Floor Tiles have an 11mm layer of insulation for support and additional thermal insulation.
SPREADER PLATES |
|
|
| ||
|
| PART | DESCRIPTION | PACK |
|
|
| NO. |
| QTY | |
|
| JGUFHSP400 | 390mm x 1000mm | 1 |
|
|
| JGUFHSP250 | 390mm x 250mm | 1 |
|
|
| JGUFHSP165 | 165mm x 1000mm | 1 |
|
Spreader Plates are available for timber flooring using either traditional joists or TJI Joists.
Spreader Plates 390 x 1,000mm and 390 x 250mm are laid across traditional joists and fixed in place using a hand stapler.
Spreader Plates 165 x 1000mm can be used with traditional and TJI joists. They are fixed to the underside of the floor using staples or screws.
Speedfit Pipe is fixed in the grooves of the plates.
When the plates and pipework have been installed, insulation is placed in the void below the plates to minimise downward heatloss.
ACTUATOR VALVE |
|
| ||
|
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY |
|
| JGUFHA(240 v) 240 v CIRCUIT ACTUATOR VALVE | 1 | |
Actuators are attached to the individual heating circuits on the manifold, providing individual control to a room or zone.
They open or close the flow of water and are controlled by a thermostat or programmer.
MASTER WIRING CENTRE |
|
|
| |||
|
| PART |
| DESCRIPTION | PACK |
|
|
| NO. |
|
| QTY | |
|
| JGUFH4ZM | MASTER WIRING CENTRE 4 ZONE | 1 |
| |
Used to connect the wiring from thermostat, actuators, boiler and pump and manage the control of the underfloor heating system.
WIRING CENTRE SLAVE |
|
|
| ||
|
| PART | DESCRIPTION | PACK |
|
|
| NO. |
| QTY | |
|
| JGUFH4ZS | WIRING CENTRE SLAVE 4 ZONE | 1 |
|
|
| JGUFH6ZS | WIRING CENTRE SLAVE 6 ZONE | 1 |
|
Connects to a Master Wiring Centre to give an additional 4 or 6 zones.
ROOM THERMOSTAT |
|
|
| |
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY | |
| JGUFHTH | ROOM THERMOSTAT WITH | 1 |
|
SET BACK TEMPERATURE REDUCTION MODE
Works in conjunction with a Centralised or Remote System Timer
A mains operated room thermostat. The temperature is set manually for ‘daytime’ temperature. A ‘set back’ mode, reducing the temperature by 4oC, is controlled by a Centralised or Remote System Timer. The Thermostat has a manual override for permanent ‘Daytime’ or permanent ‘Set back’ temperature and can be used in conjuncton with a Wet Area Probe.
WET AREA PROBE + COVER |
|
| |||
|
| PART | DESCRIPTION | PACK |
|
|
| NO. |
| QTY |
|
|
| JGUFHTHKIT | WET AREA PROBE + COVER | 1 |
|
Used in conjunction with the Room Thermostat with set back control or Digital Room Thermostat, the kit is used in areas where the use of 240v would be a problem.
A 3 metre long cable connects a non electrical probe to a room thermostat.
DIGITAL ROOM THERMOSTAT |
|
|
| |
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY | |
| JGUFHTHDIG | DIGITAL ROOM | 1 |
|
THERMOSTAT
Works in conjunction with a Centralised or Remote System Timer
A mains operated room thermostat. The temperature is set manually to ‘Daytime’ temperature and reduced by 4oC to ‘Setback’ temperature by a Centralised or Remote System Timer. It has a manual override for permanent ‘Daytime’ or permanent ‘Setback’ temperature and can be used in conjunction with a Wet Area Probe.
PROGRAMMABLE ROOM THERMOSTAT |
| |||
|
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY |
|
| JGUFHPRS | PROGRAMMABLE ROOM | 1 |
|
|
| THERMOSTAT |
|
The Programmable Room Thermostat is a fully programmable electronic room thermostat which can be set to give each zone an individual time and temperature control.
CENTRALISED SYSTEM TIMER |
|
|
| ||
|
| PART | DESCRIPTION | PACK |
|
|
| NO. |
| QTY | |
|
| 1 |
| ||
|
| To be used with a Speedfit Set Back Thermostat. |
|
| |
If specified, one timer is needed for each manifold in the system. The timer provides centralised control of the set back functions for the whole manifold via a digital programmer. The timer acts as a timed switch to alternate between ‘daytime’ and ‘Set Back’ time.
REMOTE SYSTEM TIMER |
|
|
| ||
|
| PART | DESCRIPTION | PACK |
|
|
| NO. |
| QTY | |
|
| REMOTE SYSTEM TIMER | 1 |
| |
A 4 channel programmer. Ideal for installations where the system timer needs to be located away from the manifold. Can also be used, via a Master Wiring Centre, to control the set back for up to 4 Speedfit Room Thermostats. On a larger system the Remote System Timer can be used to replace a number of individual programmers, controlling say underfloor heating, radiators and hot water.
UNDERFLOOR HEATING SPARE PARTS |
|
| ||
| PART | DESCRIPTION | PACK |
|
| NO. |
| QTY |
|
SPUFH1 | MIXING VALVE CARTRIDGE KIT | 1 |
| |
SPUFH2 | PUMP PACK FLOW TEMP GAUGE | 1 |
| |
SPUFH3 | OVER HEAT STAT | 1 |
| |
SPUFH4 | MANIFOLD FLOWMETER | 1 |
| |
SPUFH5 | MANIFOLD BALANCING VALVE | 1 | 24 | |
SPUFH6 | DUST CAP FOR BALANCING VALVE | 1 | ||