GSW POWER VENTED GAS FIRED WATER HEATER IV Water Pipe Connections, Gas Service

Page 8

Ensure that there is no movement of the clamped assembly once it is completed.

IV) Water Pipe Connections

Water piping and fittings should be installed as shown in Figure 8.

1.Close main water supply and drain the piping system where water heater is to be connected.

2.Water heater “inlet” and “outlet” are identified in the top cover (see figure 8).

3.When attaching solder (sweat) fittings, DO NOT APPLY

HEAT DIRECTLY TO THE WATER HEATER

NIPPLES or the plastic liners will be damaged. Sweat adapters to the first section of the water piping before threading onto the water heater.

4.Install a manual shut-off valve in the cold water supply line. It is good plumbing practice to include unions at the hot and cold connections as shown. (Fig. 8)

5.IMPORTANT: Before putting the water heater into service, make sure that a properly rated and sized temperature and pressure relief valve is installed in the designated fitting in the water heater. The relief pressure marked on the relief valve must not exceed that stated on the rating plate of the water heater.

IMPORTANT: The relief valve must be connected to a discharge or drain pipe no smaller in size than the outlet of the relief valve. This pipe must not be valved, plugged, allowed to freeze, or be restricted in any way. Terminate close to a drain of adequate capacity.

The relief valve is necessary to avoid excessive water pressure or water temperature from developing. Such a condition could cause serious personal injury due to scalding or serious physical damage to the water heater. This safety device shall be checked annually for proper operation.

Check local Codes.

6.With water piping installed, check that a hot water faucet served by the water heater is open and that the heater drain valve is closed. Open the cold water supply valve and fill the

water heater and piping system with water. When an uninterrupted stream of water flows from the faucet, the system is full. Close faucet. Check for leaks and repair as necessary.

7.Connect a hose to the drain valve and connect to drain. Open drain and let water run until clear to flush out any foreign

matter that may have entered the system. Once flushed, close the drain valve and disconnect hose.

V)Gas Service

Gas piping and fitting shall be installed as shown in Figure 9. Check that a properly sized gas meter and regulator are available to service the water heater. If other appliances are using the same meter and regulator, ensure that the capacity of the meter and regulator matches that of the combined input of all appliances connected to it. The gas control supplied with this water heater is designed for a maximum inlet pressure of 0.5 p.s.i. (14" water column).

-8-

Image 8
Contents Superflue Page Installation Code Requirements Safety WarningsIntroduction Important Consumer NoticeLocation and Clearances Check Local CodesHydrogen GAS can be Produced in a Combustion Air Supply Ducts Louvers and GrillsAir Requirements for Canadian Installations Power Vent Connection Supported Venting can Pose a Safety HazardVenting Instructions Or Bending of ANY SectionHeat Directly to the Water Heater Gas ServiceIV Water Pipe Connections Gas Pressure Electrical SupplyIf OVER-PRESSURIZATION has Occurred Purging CautionVI Lighting and Operating Instructions Read Before ProceedingInitial Start Up Performance ChecksCondensation Cathodic Protection Anode Hot Water OdourNot Enough or No Hot Water To inspect or change an anodeWater Temperature is Too Hot Vent MaintenanceEnergy Cut-off Control E.C.O Water Heater Makes NoiseBurner Maintenance Installation Page

POWER VENTED GAS FIRED WATER HEATER specifications

The GSW Power Vented Gas Fired Water Heater is a robust and reliable choice for households seeking efficient hot water solutions. Renowned for its innovation and performance, this water heater is engineered to provide an uninterrupted supply of hot water while ensuring safety and energy efficiency.

One of the standout features of the GSW Power Vented model is its power venting technology. This system utilizes a blower motor to expel combustion gases from the tank, allowing for flexible installation options. Homeowners can position the unit in basements, attics, or any area with limited venting options without compromising safety or efficiency. The advanced power venting system also significantly reduces backdraft issues that are common in traditional venting systems.

The water heater boasts high energy efficiency ratings, which translates into lower utility bills. This is achieved through its durable insulation and innovative heat-trapping design. The GSW Power Vented water heater features a unique heat exchanger that maximizes heat transfer while minimizing heat loss. This means that less energy is required to heat the water, making it not only environmentally friendly but also cost-effective over the long term.

Safety is paramount with the GSW Power Vented Gas Fired Water Heater. It is equipped with a robust flammable vapor sensor technology that detects flammable vapors near the heater, ensuring that the unit operates safely in areas where flammable materials may be present. Additionally, the water heater is designed with a reliable thermostat that maintains the desired water temperature while preventing overheating.

Another key characteristic of this water heater is its impressive recovery rate. With the ability to heat large quantities of water quickly, it supports multiple fixtures and appliances simultaneously, making it an excellent choice for families with higher hot water demands.

Furthermore, GSW offers various capacity options to cater to different household sizes and needs. Whether you are upgrading your current water heating solution or installing one in a new home, the GSW Power Vented Gas Fired Water Heater provides essential features that ensure convenience, efficiency, and safety. With its combination of innovative technologies and practical design, it stands out as a reliable and effective choice for today’s homeowners seeking hot water solutions.