Electrical Connections

FIXED BRACKETS

WALL MOUNTED BRACKETS

FIXING SCREW

SLIDING PLATE MESH

DIRECTION OF MOVEMENT MOUNTING HOLE

Split Console installation instructions

•A 16A mains cable is connected to the indoor unit.

•If this cable is too short, a qualified electrician should replace it.

•An interconnecting cable complying with local wiring codes, should be connected between the indoor and outdoor units.

1.Connect the brown wire to terminal 1

2.Connect the blue wire to terminal 2

3.Connect the earth wire to the terminal marked

NOTE.

•An electrical isolator must be installed close to the condensing unit.

•Ensure that the supply voltage is 230V 50 Hz.

•The unit must be earthed.

•Field wiring and connections must comply with local codes.

•Only connect one unit to a circuit and use only the recommended circuit breaker size.

•The evaporator and condenser must be con- nected through the same circuit breaker.

•Please consult a qualified electrician.

INSTALLATION OF THE INDOOR UNIT.

•Select the most suitable position for uniform air

distribution, and one that requires the shortest in- terconnecting tubing and condensate drain pipe. When the required interconnecting piping is longer than 9m. an additional 20g/m of refrigerant should be added. The maximum recommended pipe length is 16 m. For longer lengths please refer to the pipe sizing manuals.

• The unit must be installed at least 100mm above floor level. Ensure that the return air outlet under- neath the unit is not obstructed.

• The unit is supplied with 2 loose and two fixed brackets for wall mounting. The brackets at the rear may be removed and there are mounting holes behind the fan assembly or optional mounting feet are available for free standing installations, if wall mounting is not a suitable option.

•Two openings are provided for the refrigerant piping and condensate drain tube. Both openings are on the right hand side of the unit and cater for rear or bottom entry.

•The copper tube connections are situated behind the fan deck assembly. To remove the assembly please proceed as follows:-

(a)Disconnect the unit from the electrical power supply.

(b)Remove the filter and the front access panel by removing the two screws at the bottom of the panel.

(c)Pull the 4 pin connector plug apart without unscrewing the electrical connections. Remove the four screws securing the fan assembly and pull the assembly out carefully.

(d)The liquid and suction lines will now be visible. The copper tubes should be fitted with flare nuts and stoppers.

(e)Measure and prepare the interconnecting piping prior to removing the stoppers. Ensure that the in- terconnecting pipes are fully insulated. After connecting, insulate the fittings with non drip tape to prevent sweating. NOTE: The unit has been pumped down after testing and only a small hold- ing charge of R22 refrigerant will be in the indoor unit. Please take precautions when remov- ing the stoppers.

(f)Connect a 19mm (internal diameter) drain pipe to the drain connection. Insulate the drain pipe where sweating could cause damage. Ensure the drain pipe is slanted to allow easy flow. Do not use traps for the condensate drain.

(g)For service and warranty purposes a duplicate serial sticker is located on the control panel door.

Part Number 059 044 specifications

Defy Appliances has consistently been at the forefront of innovative home solutions, and their Part Number 059 044 exemplifies this commitment. This appliance is designed with functionality and efficiency in mind, catering to various consumer needs while ensuring exceptional performance.

One of the main features of the Defy 059 044 is its energy-efficient design. As homeowners become increasingly conscious of their environmental footprint, energy efficiency has become a key selling point. The 059 044 model integrates advanced technology to reduce power consumption without compromising performance. This appliance is engineered to meet stringent energy-saving standards, making it a responsible choice for environmentally-minded consumers.

In terms of capacity, the Defy 059 044 boasts a spacious interior that accommodates a variety of cooking and storage needs. This feature is particularly beneficial for busy households, where meal preparation and storage can become a challenge. The adjustable shelving and customizable compartments enhance usability, allowing users to organize their space effectively.

Another notable technology within the Defy 059 044 is its advanced cooling system. This system ensures even temperature distribution, which is crucial for preserving food quality and minimizing spoilage. The appliance is equipped with a frost-free mechanism that eliminates the need for manual defrosting, subsequently saving time and effort for users.

Additionally, the Defy 059 044 prioritizes user-friendly controls. The intuitive interface is designed for ease of use, with straightforward settings that allow users to operate the appliance confidently. The clear display ensures that even those unfamiliar with technology can navigate its features without difficulty.

The design of the Defy 059 044 is both modern and aesthetically pleasing, making it a perfect addition to any contemporary kitchen. Its sleek exterior and neutral color options allow it to blend seamlessly with various decor styles, enhancing the overall look of the space.

Moreover, the Defy 059 044 is built to last, reflecting the brand's reputation for durability and reliability. The high-quality materials used in its construction ensure that the appliance can withstand daily use, providing consumers with peace of mind.

In summary, the Defy Appliances Part Number 059 044 is a well-rounded appliance offering energy efficiency, ample storage, advanced cooling technology, user-friendly controls, and a modern design. It stands as a testament to Defy's dedication to creating appliances that simplify life while delivering exceptional value.