Integra DTR-5.8 instruction manual First Time Setup, Press Enter, Speaker detect results appear

Page 42

First Time Setup—Continued

2

3

Put the speaker setup micro- phone at measurement point 

(page 41), and connect it to the Setup Mic jack.

Auto Speaker Setup

AUDYSSEY

Please place microphone at center

of listening area at ear height.

Push Enter : Next

Notes:

•Make sure the microphone is hori- zontal.

•If there’s an obstacle between the microphone and any speaker, the automatic setup will not work cor- rectly. Set up the room as you would when enjoying a DVD.

•Positioning the microphone close to where your ears would normally be will provide better results. You can adjust the height of the microphone by using a tripod or level table.

Press [Enter].

The automatic speaker setup starts.

Auto Speaker Setup

AUDYSSEY

Do not unplug microphone.

Please keep quiet.

Now Measuring. . .

A test tone is output by each speaker in turn, as the Audyssey 2EQ function determines which speakers are con- nected. This takes a few minutes.

Note:

If any extraneous noise is picked up by the microphone, the automatic setup may not work correctly, so don’t make any noise.

4

5

The speaker detect results appear.

 

Auto Speaker Setup

 

 

 

 

AUDYSSEY

 

 

 

 

 

 

 

 

- - - - - SP Detect Result - - - - -

 

 

 

FL

: Yes

FR

: Yes

 

 

 

SL

: Yes

SR

: Yes

 

 

 

SBL

: Yes

SBR

: Yes

 

 

 

C

: No

SW

: Yes

 

 

 

 

 

 

 

 

 

 

Next

 

 

 

 

 

 

Retry

 

 

 

 

 

 

Cancel

 

 

 

 

 

 

 

 

 

 

 

 

 

“Yes” means that the speaker was detected. “No” means that no speaker was detected.

If you agree with the results, use the Up and Down []/[ ] but- tons to select Next, and then press [Enter].

The options are:

Next:

Proceed to the next step.

Retry:

Return to step 2 and try again.

Cancel:

Cancel the automatic speaker setup.

The following screen appears.

Auto Speaker Setup

AUDYSSEY

Please place microphone at right end

of listening area at ear height.

Push Enter : Next

Move the speaker setup micro- phone to measurement point 

(page 41), then press [Enter].

Audyssey 2EQ performs more mea- surements. This takes a few minutes.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents DTR-5.8 Important Safety Instructions AvisPrecautions PowerFCC Information for User Supplied Accessories Make sure you have the following accessoriesTable of Contents Processing FeaturesAmplification ConnectionsFront & Rear Panels Front PanelFront & Rear Panels Display Rear Panel Remote Control FRONT, CENTER, SURR, and Surr BackRemote Controller Installing the BatteriesAiming the Remote Controller Remote Controller Using the Remote ControllerReceiver/Tape Mode  Zone 2 button Remote Mode buttonsButtons used when the Tuner input is selected  Standby/On buttonDVD Mode  Disc/Album +/- button CD/MD/CDR/Dock ModeTo select the input source, press  Arrow / and Enter buttonsAbout Home Theater Enjoying Home TheaterOptical Digital Jacks AV Connection Color Coding Connecting the AV receiverAbout AV Connections AV Cables & JacksConnecting the AV receiver Connecting Your SpeakersSpeaker Connection Precautions Connecting the Speaker CablesStrip about 5/8 15 mm Bi-amping the Front Speakers Bi-amping Speaker HookupConnecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shown North American modelsConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaUsing a TV/FM Antenna Splitter Which Connections Should I Use? Connecting Both Audio & VideoHdmi Monitor Setting Set to Yes Video Connection FormatsHdmi Monitor Setting Set to No Audio Connection FormatsAudio Connection Connecting Your TV or ProjectorVideo Connection HintConnecting a DVD Player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Game Console Connecting a Camcorder or Other Device Camcorder, etcSupported Audio Formats Connecting Components with HdmiAbout Hdmi About Copyright ProtectionVideo Signals Audio SignalsMaking Hdmi Connections Connecting a CD Player or Turntable CD Player or Turntable MM with Built-in Phono Preamp StepConnecting an RI Dock RI Dock with video RI Dock without videoConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Power AmplifierConnecting Components Connecting the RS232 PortConnecting the Power Cord Turning On the AV Receiver Turning On and StandbySmooth Operation in a Few Easy Steps First Time Setup Automatic Speaker Setup Audyssey 2EQUsing Audyssey 2EQ Measurement Points Speaker detect results appear First Time SetupPress Enter Following screen appearsReview SP Distance Review SP ConfigDisconnect the speaker setup microphone Review SP LevelWrite Error Error MessagesSpeaker Detect Errors Ambient noise is too highChanging the Speaker Settings Manually Using a Powered SubwooferReviewing the Results About the Onscreen Setup Menus SubmenusHdmi Monitor Then press Enter Video Input SetupHdmi Input Setup Hdmi Input menu appearsComponent Video Setup Put Assign, and then press Enter Digital Input SetupPress the Receiver button fol Lowed by the Setup button Buttons to select 4. DigitalSpeaker Settings menu appears Speaker SettingsPress the Receiver button, fol- lowed by the Setup button Changing the Input DisplayWhen you’ve finished, press the Setup button TV Format Setup Not North American modelOSD Setup menu appears Miscellaneous, and then press EnterAM Frequency Step Setup Australian model Use the Left and Right / buttons to selectBasic Operations Selecting the Input SourceBasic Operations Using the Multichannel DVD InputAdjusting the Bass & Treble Displaying Source InformationUsing Headphones Setting the Display BrightnessUsing the Sleep Timer Muting the AV receiverListening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioSelect the preset that you want to delete Selecting PresetsDeleting Presets Listening to the RadioListening Mode / buttons Using the Listening ModesSelecting with the Remote Controller Selecting Listening ModesUsing the Listening Modes Listening Modes Available for Each Source FormatAnalog and PCM Sources Dolby Digital, Dolby Digital Plus, and TrueHD Sources All Ch Stereo Full MonoDTS and DTS 96/24 Sources Studio-Mix *3 TV Logic *3 All Ch Stereo Onkyo Full MonoDTS-HD High Resolution Audio and DTS-HD Master Audio Sources About the Listening Modes Onkyo Original DSP Modes Neural Surround North American models onlyRecording AV RecordingRecording Separate AV Sources Advanced Operations Using the CinemaFILTERAdjusting Individual Speaker Levels Dolby Digital, Dolby Digital PlusAdvanced Setup Speaker SetupSpeaker Settings Low-Pass Filter for the LFE Channel Advanced SetupSetup menu closes Double BassTance, and then press Enter Repeat for all speakers Press the Setup buttonSpeaker Distance Use the Left and Right Buttons to selectBration, and then press Enter Speaker Level CalibrationButtons to select 4. Level Cali Level Calibration menu appearsEqualizer Setting Speaker Setup menu appearsButtons to select 4. Analog Mul Multichannel DVD Input SettingsSubwoofer Input Sensitivity Tich, and then press EnterAudio Adjust Functions Tone Control SettingsInput Channel Settings PLIIx/Neo6 Music Mode Settings Dolby EX Input Signal SettingTheater-Dimensional Listening Setting Assigning Listening Modes to Input SourcesSource Setup IntelliVolumeWhen you’re finished, press the Setup button Press Enter, and use the Left Right / buttons toLiseconds in 2 millisecond steps Buttons to select 1. Volume Volume Setup/OSD SetupVolume Setup Volume Setup menu appearsOSD Setup Hdmi Setup Changing the AV receiver’s IDXvYCC Hdmi Audio OutLip Sync ControlChanging the Remote Controller’s ID Lock SetupDigital Input Signal Formats Buttons to select 8. Lock Setup, and then press EnterUsing Another Amp in Zone Connecting ZoneSetting the Powered Zone Using Only Speakers in ZoneSetting the Zone 2 Out Buttons to select 2. Zone2,Zone2 menu appears Using Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV receiver On the AV receiver, use Adjusting the Volume for ZoneAdjusting the Tone and Balance for Zone Zone 2 Level / buttons12V Trigger Setting for Each Input Source Using the 12V Triggers in Zone 2 and the Main RoomDelay Main menu appears onscreenUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Controller Remote Control Codes for Integra Components Connected viaResetting Remote Mode Buttons Controlling Other Components Previous  TV VOL CH + TV InputVideo Section SpecificationsAmplifier Section Tuner SectionTroubleshooting Troubleshooting Onscreen menus don’t appear Remote controller doesn’t workThere’s no picture from a source connected to an Hdmi Immediate display does not appearCan’t record Sound changes when I connect my head- phonesSpeaker volume cannot be set as required There’s no soundMemo Memo 3 4 4 5 0

DTR-5.8 specifications

The Integra DTR-5.8 is a high-performance AV receiver that stands out in the crowded home theater market. Known for its excellent sound quality and advanced features, this model is tailored for audio enthusiasts who demand fidelity and functionality.

At the heart of the DTR-5.8 is its robust amplification system, delivering a powerful 105 watts per channel into 8 ohms. This ensures that it can easily drive a variety of speakers, whether for subtle background music or explosive cinematic soundtracks. The receiver is equipped with a 7.2 channel output, allowing users to set up a surround sound system that includes additional subwoofers for deeper bass response.

One of the standout features of the DTR-5.8 is its support for advanced surround sound formats, including Dolby Atmos and DTS:X. These immersive audio technologies create a three-dimensional soundstage, enabling users to experience cinema-like audio at home. The receiver also supports Dolby TrueHD and DTS-HD Master Audio, ensuring high-definition sound quality for Blu-ray and other high-resolution formats.

Regarding connectivity, the Integra DTR-5.8 offers a wide range of options, including multiple HDMI inputs with 4K upscaling capabilities. This allows users to connect a variety of source devices, from game consoles to streaming boxes, with high resolution and ease. The HDMI ports also support HDCP 2.3, ensuring compatibility with the latest content protections.

Another key characteristic of the DTR-5.8 is its multi-room audio capability. With built-in Zone 2 audio output, users can enjoy music in different areas of their home simultaneously. Additionally, the receiver supports streaming services like Spotify, Tidal, and Pandora, allowing for seamless access to a vast library of music.

The user interface is intuitive, thanks to an on-screen display and a well-organized remote control. Furthermore, the DTR-5.8 supports network features, including Wi-Fi and Ethernet connectivity for easier setup and access to online content, as well as integration with smart home systems.

In summary, the Integra DTR-5.8 is a feature-rich AV receiver that offers phenomenal sound quality, versatile connectivity options, and support for the latest audio formats. Whether you're a movie buff or a music lover, the DTR-5.8 is designed to enhance your home entertainment experience, making it a top choice for anyone looking to build a premier home theater system.
Top Page Image Contents