Integra DTM-5.3 appendix Connecting the power, Standby indicator Standby/On button

Page 16
Connecting the power

Connecting the power

Before plugging in the unit, confirm that all connections have been made properly.

Before turning on the power, be sure that the VOLUME knob is fully turned counterclockwise.

Turning on this unit’s power may cause a momentary power surge, which might interfere with other electrical equipment, such as comput- ers. If so, connect the unit to a wall outlet on a different circuit.

Plug the power cord into the AC INLET, then plugging the power cord plug into an AC outlet puts the unit in Standby mode (the Standby indicator is lit).

Pressing the Standby/On button turns on the unit and lights up the display. If this switch is pressed again, the unit returns to Standby mode.

Standby indicator

Standby/On button

Master Volume

Standby indicatorStandby/On

Standby

Speakers

A

B

 

 

 

 

 

 

 

 

Zone 2

Off

Display

Direct

Tuning

Memory

FM Mode

Character

Phones

 

Video

Tape 2

 

FM

 

 

Bass

Treble

Balance

DVD

Monitor

Tape 1

AM

Phono

CD

 

 

 

 

 

 

 

 

 

 

 

L

R

DTM-5.3

On the remote controller, press the On button to turn on the power to the DTM-5.3, then press the Standby button to place the unit in Standby mode.

On button On button  Standby buttonManual backgroundManual backgroundManual background Standby button

To wall outlet

16

Image 16
Contents Contents Before usingFacilities and connections Setup and operationImportant Safeguards AVISPrecautions For U.S. modelFor Canadian model Modèle pour les CanadienFeatures Supplied accessoriesRemote controller description Facilities and connectionsStandby indicator Zone 2 button and indicator, Off buttonRemote control sensor Display Front panel descriptionDirect Tuning button Alphabetic letters/symbols buttonsMaster Volume dial Tuning buttonsRear panel description ZONE 2 CONTROL SELECTORA-BUSREADY ZONE 2 OUTREMOTE CONTROL Rear panel descriptionVIDEO IN/OUT MONITOR OUTConnecting components Example of audio equipment connectionConnecting components Example of video equipment connectionsConnecting speakers Connecting the speakerConnecting the speaker cable Connecting a subwooferConnecting antennas Connecting the AM antenna cableConnecting an FM outdoor antenna Connecting the included antennasZone 2 connections Connecting the remote zone ZoneZone 2 Control Selector OUT DTM-5.3 from connecting block Mini plug cableDTM-5.3 Standby indicator Standby/On button Connecting the powerOn button Standby button Installing the batteries Installing the remote controller batteriesRemote controller operation Listening to your favorite source Basic operationsDirect change function Listening using the headphones Mute function Remote controller onlySleep function Remote controller only Basic operationsTuning the radio Direct tuning Tuning the radio Manual tuningReceiving stations Listening to stereo radio stations FM only Receiving stationsProgramming radio stations Selecting preset stations Cancelling preset stationsPreset Receiving stationsCleaning all characters Entering station namesEntering characters Changing an entered characterRecording an audio source Recording a sourceTape-to-Tapedubbing Recording a source DTM-5.3VCR VIDEO DTM-5.3Using a graphic equalizer Using Tape 2 MonitorMonitoring during recording Zone 2 operation from the main room Enjoying music in the remote zoneZone 2 A-BUSor IR operation in the zone 2 room Using the remote controller Setting the ID numberChecking the remote controller’s ID Programming the ID numberControlling an Integra/Onkyo CD player Controlling other componentsControlling an Integra/Onkyo DVD player Controlling other components Controlling an Integra/Onkyo cassette tape deckTroubleshooting guide AppendixTrouble CauseREMOTE CONTROLLER RC-477S SpecificationsAMPLIFIER SECTION GENERAL