Integra DTM-5.3 appendix Receiving stations, Tuning the radio Manual tuning

Page 20

Receiving stations

Receiving stations

Please make sure that the

T-2 MONITOR

and AUDIO MUTE indicators are not lit.

	For the remote controller, press the RCVR/Tape mode button before performing the
	procedure in this section.	Number
		Number
	Tuning	buttons
	Tuning	RCVR/Tape
	Number buttons	RCVR/Tape
	Number buttons
		DRCT
		Tune

Master Volume

Tuning

Tuning

Standby/On

1 ABC

2 DEF

3 GHI

Down

Up

4 JKL

5 MNO

6 PQR

7 STU

8 VWX

9 YZ-

Standby

Direct Tuning

0/10

/

Scan

Speakers

A

B

Clear

Zone 2

Off

Display

Direct

Tuning

Memory

FM Mode

Character

Phones

DVD

Video

Tape 2

Tape 1

FM

AM

Phono

CD

Bass

Treble

Balance

Monitor

FM

AM

L

R

DTM-5.3

FM AM Direct Tuning

Tuning the radio (Manual tuning)

When the frequency is not known (Manual tuning)

1 Press the FM or AM button.

FMAM

or

2 Use the	Tuning	buttons (or Tuning Down and Up
buttons on the remote controller) to change the fre-
quency.
(Up).....the frequency increases.

Tuning the radio (Direct tuning)

When the frequency is known (Direct tuning)

1 Press the FM or AM button.

FMAM

or

2Press the Direct Tuning button (or DRCT Tune button on the remote controller).

The “-- --” will ﬂash for 16 seconds in the frequency display.

FM MUTE TUNED

(Down).....the frequency decreases.

Direct Tuning

ON STEREO

MHzCH

FM MUTE	TUNED
ON	STEREO
Tuning	MHz	CH
	TUNED
	kHz
		CH

•The frequency is changed in 100 kHz steps in FM and 10 kHz in AM each time a tuning selector button is pressed.

•If a button is held continuously for more than 0.5 seconds, the frequencies are scanned automatically (FM auto tuning mode). When a broadcast is received, scanning stops.

3Enter the frequency by pressing the number buttons while the cursors are ﬂashing.

1 ABC	2 DEF	3 GHI	FM MUTE	TUNED
			ON	STEREO
4 JKL	5 MNO	6 PQR
				MHz	CH
7 STU	8 VWX	9 YZ-
			FM MUTE	TUNED
	0/10 /		ON	STEREO
				MHz	CH

Example: 88.1MHz 8 ➔ 8 ➔ 1

•If you enter a frequency that is out of range, the unit will return to the previous frequency. If this happens, repeat the procedure.

20

Image 20

Contents Contents Before usingFacilities and connections Setup and operationImportant Safeguards AVISPrecautions For U.S. modelFor Canadian model Modèle pour les CanadienFeatures Supplied accessoriesRemote controller description Facilities and connectionsStandby indicator Zone 2 button and indicator, Off buttonRemote control sensor Display Front panel descriptionDirect Tuning button Alphabetic letters/symbols buttonsMaster Volume dial Tuning buttonsRear panel description ZONE 2 CONTROL SELECTORA-BUSREADY ZONE 2 OUTREMOTE CONTROL Rear panel descriptionVIDEO IN/OUT MONITOR OUTConnecting components Example of audio equipment connectionConnecting components Example of video equipment connectionsConnecting speakers Connecting the speakerConnecting the speaker cable Connecting a subwooferConnecting antennas Connecting the AM antenna cableConnecting an FM outdoor antenna Connecting the included antennasZone 2 Control Selector Connecting the remote zone ZoneZone 2 connections DTM-5.3 from connecting block Mini plug cableOUT DTM-5.3 On button Standby button Connecting the powerStandby indicator Standby/On button Remote controller operation Installing the remote controller batteriesInstalling the batteries Direct change function Basic operationsListening to your favorite source Listening using the headphones Mute function Remote controller onlySleep function Remote controller only Basic operationsReceiving stations Tuning the radio Manual tuningTuning the radio Direct tuning Programming radio stations Receiving stationsListening to stereo radio stations FM only Selecting preset stations Cancelling preset stationsPreset Receiving stationsCleaning all characters Entering station namesEntering characters Changing an entered characterTape-to-Tapedubbing Recording a sourceRecording an audio source Recording a source DTM-5.3VCR VIDEO DTM-5.3Monitoring during recording Using Tape 2 MonitorUsing a graphic equalizer Zone 2 A-BUSor IR operation in the zone 2 room Enjoying music in the remote zoneZone 2 operation from the main room Using the remote controller Setting the ID numberChecking the remote controller’s ID Programming the ID numberControlling an Integra/Onkyo DVD player Controlling other componentsControlling an Integra/Onkyo CD player Controlling other components Controlling an Integra/Onkyo cassette tape deckTroubleshooting guide AppendixTrouble CauseREMOTE CONTROLLER RC-477S SpeciﬁcationsAMPLIFIER SECTION GENERAL