Carrier Access 52P owner manual Electrical Data, ALL Units, Voltage Supply

Page 4

ELECTRICAL DATA

ELECTRICAL SHOCK HAZARD

DO NOT alter cord or plug, and DO NOT use an extension cord. Personal injury or damage to the unit may result.

Be sure that your outlet matches the appropriate blade configuration of the supplied plug and that it is within reach of the service cord. A hardwire kit is available as an accessory to change cord-connected units to hardwired units. (See Accessories table on page 14.)

IMPORTANT: All standard cord-connected 265-v units will require a field-installed electrical sub- base accessory.

ALL UNITS

■WIRE SIZE — Use recommended wire size given in Table 1 and install a single branch circuit. All wiring must comply with local and national codes. All units are designed to operate off single branch cir- cuits only.

NOTE: Use copper conductors only.

■GROUNDING — For safety and protection, the unit is grounded through the service cord plug or through separate ground wire provided on hardwired units. Be sure that the branch circuit or general purpose outlet is grounded.

TABLE 1 — SUGGESTED BRANCH CIRCUIT

WIRE SIZES*

NAMEPLATE AMPS

AWG WIRE SIZE†

7.0 to 12

14

12.1 to 16

12

16.1 to 24

10

LEGEND

AWG — American Wire Gage

*Single circuit from main box.

†Based on copper wire at 60 C temperature rating.

VOLTAGE SUPPLY

Check voltage supply at outlet. For satisfactory re- sults, the voltage range must always be within the ranges found on the data information plate (Figure 1).

■CORD-CONNECTED UNITS — The 250-v field- supplied outlet must match the plug for the standard 208/230-v units and be within reach of the service cord. The standard cord-connected 265-v units require an accessory electrical subbase for operation. See Accessories table, page 14, for subbase selection. Refer to Table 2 for proper receptacle and fuse type.

TABLE 2 — RECEPTACLES AND FUSE TYPES — 250,265 VOLTS

RECEPTACLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15 Amps

20 Amps

30 Amps

15 Amps

20 Amps

30 Amps

RATED VOLTS

250

 

250

 

250

 

265

265

265

 

TIME-DELAY TYPE

15

 

20*

 

30

 

15

20

30

 

 

FUSE (or HACR Circuit Breaker)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LEGEND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HACR — Heating, Air Conditioning, Refrigeration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*May be used for 15-amp applications if fused for 15 amp.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Contents Packaged Terminal AIR Conditioners Heat PumpsUnit Inspection GeneralFront Panel Model Number Nomenclature ALL Units Electrical DataVoltage Supply Installation Chassis InstallationLocation of Shipping Tape On Vent Door Wall Thermostat Installation Install Thermostat All remote control unitsOperation Comfort ControlsOperating Controls Operating Modes See FiguresCare and Maintenance INDOOR-AIR Inlet FiltersExternal Parts Internal PartsPreventative Maintenance Troubleshooting Possible Causes Solutions Unit does not StartAccessories Accessory Form Number Part Number DescriptionCarrier Copyright 2002 Carrier Corporation

52P specifications

Carrier Access 52P is a powerful networking solution designed for service providers and enterprises needing reliable, high-speed connectivity. This device plays a vital role in the ever-evolving landscape of telecommunications, offering advanced features that accommodate various network configurations.

One of the main features of the Carrier Access 52P is its support for multiple WAN technologies. This device can seamlessly integrate with various access technologies, including T1, DSL, and cable. This versatility allows network operators to utilize existing installations while improving overall network efficiency. The ability to combine multiple WAN connections through load balancing maximizes bandwidth and ensures uninterrupted service, which is crucial for businesses that rely heavily on internet connectivity.

The 52P is equipped with intelligent routing capabilities, enabling it to make real-time decisions based on traffic conditions. This Smart Routing feature ensures that critical data is prioritized, enhancing the performance of voice and video applications during peak usage times. The built-in Quality of Service (QoS) mechanisms further support this feature by allocating bandwidth according to user-defined policies, thereby reducing latency and jitter for time-sensitive applications.

Security is another essential aspect of the Carrier Access 52P. The device supports robust security protocols such as IPsec and SSL VPNs, which help protect sensitive data as it traverses the network. Its firewall capabilities provide further defense against unauthorized access, making it an ideal choice for organizations demanding high security levels.

The 52P also boasts a user-friendly interface for configuration and management, allowing network operators to monitor performance and make necessary adjustments with ease. This simplicity is complemented by network management features such as SNMP support and extensive logging capabilities, enabling proactive maintenance and fast troubleshooting.

Furthermore, the Carrier Access 52P is designed for scalability. As demand for bandwidth continues to grow, this device can accommodate future upgrades without requiring a complete system overhaul. This forward-thinking design ensures that businesses can adapt to changing conditions in a cost-effective manner.

In conclusion, the Carrier Access 52P is a robust solution that meets the demands of modern businesses and service providers. With its multi-WAN support, intelligent routing, security features, and user-friendly management tools, it stands out as a reliable choice for ensuring optimal connectivity and performance in dynamic networking environments.
Top Page Image Contents