Carrier Access 52P owner manual Troubleshooting, Possible Causes Solutions Unit does not Start

Page 13

TROUBLESHOOTING

 

 

POSSIBLE CAUSES

SOLUTIONS

UNIT DOES NOT START

 

• Unit may have become unplugged

• Check that plug is securely in wall receptacle.

• Fuse may have blown

• Replace the fuse. See Note 1.

• Circuit breaker may have been tripped

• Reset circuit breaker. See Note 1.

• Unit mode dial may be set to the OFF position

• Switch mode dial to an operating mode.

UNIT NOT COOLING/HEATING ROOM

 

• Unit air discharge section is blocked

• Make sure that curtains, blinds or furniture are not restricting or

 

blocking unit airflow.

• Temperature setting is not high or low enough

• Reset to a lower or higher temperature setting.

•Unit air filters are dirty

•Room is excessively hot or cold when unit is started • Allow sufficient amount of time for unit to heat or cool the room. Start heating or cooling early before outdoor temperature, cooking heat or gatherings of people make room uncomfortable.

•Vent door left open• Close vent door.• Remove and clean filters.

UNIT MAKING NOISES

• Clicking, gurgling and whooshing noises are normal during operation of

 

unit.

WATER DRIPPING OUTSIDE

• If a drain kit has not been installed, condensation run-off during

 

very hot and humid weather is normal. See Note 2. If a drain kit

 

has been installed and is connected to a drain system, check

 

gaskets and fittings around drain for leaks and plugs.

WATER DRIPPING INSIDE

 

• Wall sleeve is not installed level

• Wall sleeve must be installed level for proper drainage of condensation.

 

Check that installation is level and make any necessary adjustments.

ICE OR FROST FORMS ON INDOOR COIL

 

• Low outdoor temperature

• When outdoor temperature is approximately 55 F or below, frost

 

may form on the indoor coil when unit is in Cooling mode. Switch

 

unit to FAN operation until ice or frost melts.

• Dirty filters

• Remove and clean filters.

NOTES:

1.If circuit breaker is tripped or fuse is blown more than once, contact a qualified electrician.

2.If unit is installed where condensation drainage could drip in an undesirable location, an accessory drain kit should be installed and connected to drain system.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Packaged Terminal AIR Conditioners Heat Pumps ContentsUnit Inspection GeneralFront Panel Model Number Nomenclature ALL Units Electrical DataVoltage Supply Chassis Installation InstallationLocation of Shipping Tape On Vent Door Install Thermostat All remote control units Wall Thermostat InstallationComfort Controls OperationOperating Modes See Figures Operating ControlsINDOOR-AIR Inlet Filters Care and MaintenanceInternal Parts External PartsPreventative Maintenance Possible Causes Solutions Unit does not Start TroubleshootingAccessory Form Number Part Number Description AccessoriesCarrier Copyright 2002 Carrier Corporation

52P specifications

Carrier Access 52P is a powerful networking solution designed for service providers and enterprises needing reliable, high-speed connectivity. This device plays a vital role in the ever-evolving landscape of telecommunications, offering advanced features that accommodate various network configurations.

One of the main features of the Carrier Access 52P is its support for multiple WAN technologies. This device can seamlessly integrate with various access technologies, including T1, DSL, and cable. This versatility allows network operators to utilize existing installations while improving overall network efficiency. The ability to combine multiple WAN connections through load balancing maximizes bandwidth and ensures uninterrupted service, which is crucial for businesses that rely heavily on internet connectivity.

The 52P is equipped with intelligent routing capabilities, enabling it to make real-time decisions based on traffic conditions. This Smart Routing feature ensures that critical data is prioritized, enhancing the performance of voice and video applications during peak usage times. The built-in Quality of Service (QoS) mechanisms further support this feature by allocating bandwidth according to user-defined policies, thereby reducing latency and jitter for time-sensitive applications.

Security is another essential aspect of the Carrier Access 52P. The device supports robust security protocols such as IPsec and SSL VPNs, which help protect sensitive data as it traverses the network. Its firewall capabilities provide further defense against unauthorized access, making it an ideal choice for organizations demanding high security levels.

The 52P also boasts a user-friendly interface for configuration and management, allowing network operators to monitor performance and make necessary adjustments with ease. This simplicity is complemented by network management features such as SNMP support and extensive logging capabilities, enabling proactive maintenance and fast troubleshooting.

Furthermore, the Carrier Access 52P is designed for scalability. As demand for bandwidth continues to grow, this device can accommodate future upgrades without requiring a complete system overhaul. This forward-thinking design ensures that businesses can adapt to changing conditions in a cost-effective manner.

In conclusion, the Carrier Access 52P is a robust solution that meets the demands of modern businesses and service providers. With its multi-WAN support, intelligent routing, security features, and user-friendly management tools, it stands out as a reliable choice for ensuring optimal connectivity and performance in dynamic networking environments.
Top Page Image Contents