Redring 320S manual Plumbing

Page 8

6.Decide the position of entry of the cold water pipe into the unit. If top, cut away the backplate.

If rear, please read the section on plumbing.

If bottom, remove the front cover (complete with knobs) and cut away the detachable corner section as shown.

7.If you have not yet done so, remove the front cover assembly by undoing the retaining screws at the top and bottom of the unit and lifting the cover off.

Your shower is provided with 2 fixing positions in the backplate (see diagram 4).

The top-fixing hole is a “key-hole” slot (another key-hole is provided for alternate fixing), and should be marked and drilled first.

Tighten top screw with head protruding about 10mm from the wall and hook the backplate over the screw head. This allows for correct and accurate alignment of your shower before marking and fixing the bottom position.

You may not wish to tighten up both screws at this stage as the holes are elongated to allow for adjustment after other connections have taken place.

b.PLUMBING

WARNING: ENSURE THAT THE MAINS WATER SUPPLY MEETS THE REQUIREMENTS BELOW BEFORE CONTINUING WITH INSTALLATION.

The heater must be connected to the mains cold water supply.

This must have a minimum running pressure of 69kPa (0.7 bar, 10 psi) and a maximum pressure of 690kPa (7.0 bar, 100 psi).

WARNING: BEFORE CONNECTING THE PIPE WORK TO THE SHOWER, ENSURE THAT THE PIPE WORK IS FULLY FLUSHED OUT.

1.Unscrew the “Red Cap” and “Washer” from the shower outlet pipe and discard them in a suitable manner. These have been used to seal the shower during transit, and are no longer required.

2.It is recommended that a WRAS (Water Regulations Advisory Scheme) listed isolating valve is fitted between the rising main and the unit.

This will allow the unit to be serviced or exchanged without having to turn off the water at the water stop valve.

3.The heater can be fed from a header tank provided this has a minimum head of 7 metres (23ft).

4.Ø15mm copper or stainless steel pipe should be used.

To avoid cross threading, DO NOT REMOVE the nut from the elbow when positioning the pipe. If top entry is required, turn the elbow 180° into the required position.

If rear entry is required, treat as top entry with an additional “Yorkshire” elbow (soldered type) for fitting into the rear channel.

In multiple installations, correct pipe work sizes should be calculated to maintain adequate flow to each shower.

5.It is in order to use a WRAS (Water Regulations Advisory Scheme) approved sealant sparingly whilst avoiding excess finding its way into the shower operating parts.

6.With stop valve connected, flush the pipe work through to remove any particles etc, before making the final connection to the shower.

Blockage in the water ways (particularly the handset and solenoid valve) will prevent the heater working properly.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Redring Active 320S Smart Technology Electric Shower Contents IntroductionHOW to USE Your Active 320S Shower Detailed If Water is TOO ColdEffect of Other Water Devices on Incoming Water Supply Effect of Seasonal Incoming Water Temperature ChangesHOW Your Active 320S Shower Works HOW to Maintain Your Active 320S Shower YOU Must Clean the Shower Handset RegularlyWhat to do if Things GO Wrong Self HelpRing 08709 000420 UK only Redring After Sales ServiceProfessional Service HOW to Install Your Active 320S Shower Fixing the Shower to the WallPlumbing These Instructions Could Result in Failure Terminal Block Page Additional Accessories Spare Parts Guarantee and Contact DetailsHOW to USE Your Active 320S Shower Summary TEL +44 0 1733 FAX +44 0 1733Leaflet No -2136-01B

320S specifications

The Redring 320S is a compact, electric instant water heater that has gained popularity for its efficiency and convenience in providing hot water on demand. With a powerful output of 3 kW, it efficiently heats water instantly, making it an ideal solution for various applications in homes, offices, and other facilities.

One of the key features of the Redring 320S is its compact size. The unit is designed to be wall-mounted, ensuring that it does not take up unnecessary space in smaller areas such as kitchenettes or bathrooms. This compact design does not compromise performance, as it can deliver a consistent and reliable flow of hot water whenever needed.

The Redring 320S utilizes innovative heating technologies to achieve fast heating times. With its advanced heating element, the device can provide hot water at a rate of approximately 3 liters per minute. This means that users can enjoy a steady supply of hot water for tasks such as washing dishes, showering, or performing other daily routines without the wait associated with traditional storage water heaters.

Another characteristic that sets the Redring 320S apart is its energy efficiency. By operating only when hot water is needed, the unit minimizes energy consumption compared to conventional systems that continuously heat a storage tank. This results in lower energy bills and a more sustainable solution for hot water generation.

The device also comes equipped with user-friendly control features, allowing users to adjust the temperature settings easily. This personalization ensures that everyone can find their ideal water temperature, enhancing comfort and convenience.

Safety is a priority with the Redring 320S, which features built-in thermal cut-out protection. This technology prevents overheating and ensures that the device operates within safe temperature limits, providing peace of mind to users.

In conclusion, the Redring 320S is a versatile and efficient instant water heater that boasts a range of features designed to meet modern demands for hot water. Its compact design, rapid heating capability, energy efficiency, user-friendly controls, and safety features make it a standout choice for anyone in need of a reliable hot water solution. Whether in a home or commercial setting, the Redring 320S delivers performance and convenience that users can rely on.
Top Page Image Contents