Horizontal Exhaust Through the Wall

1.NOTE: Use only listed type “PL” or “L” pellet venting products. Failure to use listed components may cause damage or personal injury or death.

2.Choose a location for your stove that meets the requirements stated in this manual and allows installation with the least amount of interference to house framing, plumbing, wiring, etc.

3.Install a non-combustible hearth pad underneath the unit extending 6 inches (15 cm) in front of and to the sides.

4.Place the stove 15” (37.5 cm) away from the wall. If the stove is to be set on a hearth pad, set the unit on it.

5.Locate the center of the exhaust pipe on the stove. Extend that line to the wall. Once you have located the center point on the wall, use a hole saw to cut a 7” (175 mm) diameter hole for a 3” (76 mm) vent pipe or an 8” (200 mm) hole for a 4” (101 mm) vent pipe.

6.Install the wall thimble as per the instructions written on the thimble. Maintain an effective vapor barrier

7.Install a 2 or 3’ (61 or 92 cm) length of 3” (76 mm) or 4” (101 mm) listed type “PL” or “L” vent pipe into the wall thimble. The pipe should install easily into the thimble.

8.Install the fresh air intake (see the section entitled OUTSIDE FRESH AIR CONNECTIONS).

9.Connect the exhaust vent pipe to the exhaust pipe on the stove.

10.All Joints in the vent system shall be fastened with (3) three screws. Seal the connection with high temperature silicone

11.Push the stove straight back, leaving a minimum of 1” (3 cm) clearance from the back of the stove to the wall. Seal the vent pipe to the thimble with high temperature silicone.

12.The pipe must extend at least 12’ (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place high temperature silicone around the pipe that passes through the thimble.

13.Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However, when the vent terminates several feet above ground level and there are no trees, plants, etc. within several feet, a 45 degree elbow can be used as termination. The elbow must be turned down to prevent rain from entering.

NOTE: Some horizontal, through the wall installations may require a “T” and 4-5 feet of

5.0”vertical pipe outside the building to help draft the stove. This may be required if a proper burn cannot be maintained, after the stove has been tested and the airflow set. This is due to back-pressure in the exhaust, caused by the air flow around the house.

16.625”

10.812”11.938”

EF-3 BAYI specifications

The Sherwood EF-3 BAYI is a remarkable integrated amplifier that stands out in the realm of audio equipment, delivering exceptional sound quality coupled with advanced technology. Renowned for its robust build and powerful performance, the EF-3 BAYI is designed both for audiophiles and casual listeners looking to elevate their audio experience.

At the heart of the Sherwood EF-3 BAYI is its high-fidelity amplification system, capable of delivering an impressive output power to drive various speaker configurations. The amplifier is engineered to produce a clean, dynamic sound that maintains clarity even at higher volume levels. Its audio performance is enhanced by advanced circuitry that minimizes distortion and ensures a natural, balanced sound across a wide frequency range.

One of the standout features of the EF-3 BAYI is its Class AB amplification technology. This design offers the best of both worlds, combining the efficiency of Class D amplification with the superior sound quality typically associated with Class A designs. This results in an amplifier that not only conserves energy but also offers a warm and engaging listening experience that appeals to critical listeners.

Additionally, the EF-3 BAYI is equipped with multiple input options, including analog RCA inputs, digital coaxial, and optical inputs, allowing users to connect a variety of audio sources. Furthermore, its built-in Bluetooth functionality enables wireless streaming from smartphones, tablets, and other Bluetooth-enabled devices, making it versatile and convenient for modern-day listening habits.

The amplifier's user-friendly interface includes clearly labeled knobs and buttons for adjusting volume, treble, and bass, empowering users to tailor the audio output to their preferences. Moreover, the sleek and contemporary design of the EF-3 BAYI ensures that it fits seamlessly into any home audio setup, making it not just an audio powerhouse but also an aesthetically pleasing addition.

Overall, the Sherwood EF-3 BAYI integrated amplifier exemplifies what modern audio technology can achieve, combining robust performance with advanced features, making it a top choice for anyone looking to enhance their auditory experience. Whether for music, movies, or gaming, the EF-3 BAYI stands ready to deliver exceptional sound quality that truly brings content to life.