Sterling Power Products 30F to 65F Overhead Process Considerations, inch 2.5 cm pipe

Page 17
FROM PROCESS

2-5 Overhead Process Considerations

If your application has chilled water or process piping above the reservoir fill and vent level, install a standpipe to a point 1’ (30 cm) above the highest point in the system.

In applications where the process or its piping is 15 feet (4.6 m) or more above the reservoir, you must take steps to prevent over-pressurization of the reservoir. This condition can occur on system shutdown when the water in the system drains into the reservoir.

To prevent this, install a check valve in the unit breaker at the high point of the return

more information.

TO PROCESS line and a vacuum line. See Figure 7 below for

Note: The reserve capacity of the reservoir can hold a volume equal to 20 feet (6.1 m)

of 1-inch (2.5 cm) pipe.

Figure 7: Overhead Piping

The reservoir vent & fill line

Vent

 

Vacuum Breaker

to be piped 12" above the highest

 

 

 

Assembly

point of the system. The vent line

 

 

 

Cap

must remain open to the atmosphere.

12"

Check

 

 

 

 

 

 

 

1/8"

 

 

 

Valve

 

 

 

 

Hole

 

 

1/4"

 

 

 

 

 

 

6" Min.

 

 

 

 

Process Return

 

 

Strainer

 

Process Supply

Add check valve if system piping extends 15 feet above reservoir.

IndicatesendendofofAECSterlpiping

piping

SMC Series Chillers

Page 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SMC Series AIR Cooled Portable Water Chillers SMC Series Chillers Safety Considerations Table of Contents Optional Graphic Panel Charts and Figures Introduction General InformationNecessary Documents Models CoveredUncrating Your New Chiller Available OptionsIf the Shipment is Incorrect Event of Shipping DamagesIf the Shipment is Not Complete Returns SMC050 Process Pump Curves SMC Cast Iron Centrifugal Pump Curve 1/3 hp 0.249 kW SMC Series Chiller Specifications Electrical Connections Chiller InstallationProcess Water Connections From ProcessProcess Water Bypass PCA Condenser Air SupplyWater Reservoir Ethylene Glycol Curve 30% Ethylene Glycol 20% Percent Volume 10%1-inch 2.5 cm pipe Overhead Process ConsiderationsRefrigeration Circuit Sequence of OperationChilled Water Circuit Remote Start/Stop Interlock High Pressure CutoutLow Pressure Cutout SMC Component Identification Piping Schematic 1 Pump with Reservoir Piping Schematic 1 Pump Without Reservoir Piping Schematic No Pump, No Reservoir PCA Startup Checklist SMC Pre-Startup ChecklistModel Gallons per minute Liters per minute ΔP psig ΔP kPa SMC Water Circuit Pressure Drop TableLED Indicators Setting the Process Water TemperatureMicroprocessor Control PV or Process Value Numeric LEDE5CK Display Key Temperature Controller KeysAT AT Key Factory default settings are P = .3, I = 7, and D = Auto-Tuning SMC Series ChillersDown Key Up KeyStandard Omron Protocol Optional CommunicationsOptional Graphic Panel Indicator LightsSwitches PC Series Lubrication Routine MaintenanceCondenser Maintenance Typical SMC Wiring Schematic SMC Wiring Schematic for Chillers with No Pump or Reservoir SMC Series Chillers Problem Cause Solution Troubleshooting GuideProblem Cause Solution PCA Unit Parts List SMC Series Chillers SMC Series Chillers Technical Assistance Parts Department

30F to 65F specifications

Sterling Power Products has established itself as a leader in the design and manufacturing of high-quality power management solutions for various applications. One of their standout products is the range of battery chargers, specifically the 30F to 65F models, which are engineered to meet the diverse needs of users, from recreational boating to commercial marine applications.

The Sterling 30F to 65F battery chargers are known for their versatility, efficiency, and advanced technology. These chargers are designed to convert a wide input voltage range into a precise DC output voltage tailored for charging various types of batteries, including lead-acid and lithium-ion. This adaptability makes them suitable for a broad spectrum of applications, ensuring that users can maintain their battery systems effectively, regardless of the environment or battery type.

A key feature of the 30F to 65F models is their smart charge technology. This technology enables the charger to automatically adjust its charging profile based on the specific needs of the battery. This ensures optimum charging efficiency while prolonging the lifespan of the battery by preventing overcharging. The units also offer multi-stage charging processes, including bulk, absorption, and float stages. This multi-stage approach helps in delivering the right amount of charge at each phase, enhancing performance and reliability.

In addition to their smart charging capabilities, Sterling products integrate advanced thermal management systems. This feature allows the chargers to operate efficiently in high-temperature environments, sensing when to reduce output to protect both the charger and the batteries. The robust construction of these units includes marine-grade enclosures that provide durability and resistance to harsh environmental conditions, making them ideal for marine and automotive use.

Furthermore, users will appreciate the ease of installation and operation. The 30F to 65F models are designed with user-friendly interfaces and clear indicators for charging status, making them accessible to both seasoned professionals and casual users. With safety features such as reverse polarity protection and short-circuit prevention, these chargers offer peace of mind during operation.

Overall, the Sterling Power Products 30F to 65F battery chargers represent a reliable and sophisticated solution for maintaining battery health across various applications. Their combination of smart technology, durability, and ease of use solidifies Sterling’s reputation as a trusted provider in the power management industry. Whether for recreational or professional use, these chargers promise efficiency and reliability to meet the demands of modern battery systems.
Top Page Image Contents