Sterling Power Products 30F to 65F installation manual High Pressure Cutout, Low Pressure Cutout

Page 19

3-3 High Pressure Cutout

The high pressure cutout is an electro-mechanical safety feature that opens the control circuit if the system condensing pressure exceeds a safe level. The chiller will automatically restart when the pressure drops back to an acceptable level.

Model

Cuts out if condensing pressure exceeds:

SMC050

275 psi (1,897 kPa)

SMC100

275 psi (1,897 kPa)

SMC150

400 psi (2,759 kPa)

IMPORTANT!

Call a refrigeration service technician to analyze

the problem if high pressure recurs.

3-4 Low Pressure Cutout

The low pressure cutout is an electro-mechanical safety feature that prevents compressor suction pressure from dropping below a preset point.

It is factory set to open the control circuit when pressure drops below a safe level. The chiller will automatically restart when the suction pressure reaches an acceptable level.

Model

Cuts out if suction pressure falls below:

SMC050

15 psi (103 kPa)

SMC100

15 psi (103 kPa)

SMC150

35 psi (241 kPa)

3-5 Remote Start/Stop Interlock

A contact is provided to allow interlocking of the SMC Series Chiller with process controls. To use this feature, remove the jumper between Terminals X1 and 1 on Terminal Block 1. Supply a switch or dry contact interlock connected in series between these two terminals. See Figure 15 and Figure 16 on pages 34 and 35 for more information.

SMC Series Chillers

Page 19

Image 19
Contents SMC Series AIR Cooled Portable Water Chillers SMC Series Chillers Safety Considerations Table of Contents Optional Graphic Panel Charts and Figures Models Covered General InformationIntroduction Necessary DocumentsUncrating Your New Chiller Available OptionsIf the Shipment is Not Complete Event of Shipping DamagesIf the Shipment is Incorrect Returns SMC050 Process Pump Curves SMC Cast Iron Centrifugal Pump Curve 1/3 hp 0.249 kW SMC Series Chiller Specifications From Process Chiller InstallationElectrical Connections Process Water ConnectionsWater Reservoir PCA Condenser Air SupplyProcess Water Bypass Ethylene Glycol Curve 30% Ethylene Glycol 20% Percent Volume 10%1-inch 2.5 cm pipe Overhead Process ConsiderationsChilled Water Circuit Sequence of OperationRefrigeration Circuit Low Pressure Cutout High Pressure CutoutRemote Start/Stop Interlock SMC Component Identification Piping Schematic 1 Pump with Reservoir Piping Schematic 1 Pump Without Reservoir Piping Schematic No Pump, No Reservoir PCA Startup Checklist SMC Pre-Startup ChecklistModel Gallons per minute Liters per minute ΔP psig ΔP kPa SMC Water Circuit Pressure Drop TablePV or Process Value Numeric LED Setting the Process Water TemperatureLED Indicators Microprocessor ControlE5CK AT AT Key Temperature Controller KeysDisplay Key Up Key Auto-Tuning SMC Series ChillersFactory default settings are P = .3, I = 7, and D = Down KeyStandard Omron Protocol Optional CommunicationsSwitches Indicator LightsOptional Graphic Panel PC Series Condenser Maintenance Routine MaintenanceLubrication Typical SMC Wiring Schematic SMC Wiring Schematic for Chillers with No Pump or Reservoir SMC Series Chillers Problem Cause Solution Troubleshooting GuideProblem Cause Solution PCA Unit Parts List SMC Series Chillers SMC Series Chillers Technical Assistance Parts Department

30F to 65F specifications

Sterling Power Products has established itself as a leader in the design and manufacturing of high-quality power management solutions for various applications. One of their standout products is the range of battery chargers, specifically the 30F to 65F models, which are engineered to meet the diverse needs of users, from recreational boating to commercial marine applications.

The Sterling 30F to 65F battery chargers are known for their versatility, efficiency, and advanced technology. These chargers are designed to convert a wide input voltage range into a precise DC output voltage tailored for charging various types of batteries, including lead-acid and lithium-ion. This adaptability makes them suitable for a broad spectrum of applications, ensuring that users can maintain their battery systems effectively, regardless of the environment or battery type.

A key feature of the 30F to 65F models is their smart charge technology. This technology enables the charger to automatically adjust its charging profile based on the specific needs of the battery. This ensures optimum charging efficiency while prolonging the lifespan of the battery by preventing overcharging. The units also offer multi-stage charging processes, including bulk, absorption, and float stages. This multi-stage approach helps in delivering the right amount of charge at each phase, enhancing performance and reliability.

In addition to their smart charging capabilities, Sterling products integrate advanced thermal management systems. This feature allows the chargers to operate efficiently in high-temperature environments, sensing when to reduce output to protect both the charger and the batteries. The robust construction of these units includes marine-grade enclosures that provide durability and resistance to harsh environmental conditions, making them ideal for marine and automotive use.

Furthermore, users will appreciate the ease of installation and operation. The 30F to 65F models are designed with user-friendly interfaces and clear indicators for charging status, making them accessible to both seasoned professionals and casual users. With safety features such as reverse polarity protection and short-circuit prevention, these chargers offer peace of mind during operation.

Overall, the Sterling Power Products 30F to 65F battery chargers represent a reliable and sophisticated solution for maintaining battery health across various applications. Their combination of smart technology, durability, and ease of use solidifies Sterling’s reputation as a trusted provider in the power management industry. Whether for recreational or professional use, these chargers promise efficiency and reliability to meet the demands of modern battery systems.