Skuttle Indoor Air Quality Products Klin manual Edit Mode Features

Page 21

ADVANCED PROGRAMMING

21

EDIT MODE FEATURES

The Edit Mode Features were designed to allow the artist to adjust the program while it is running. These features are generally used after a visual inspection of the project indicates a change in the program is needed. Edit Mode Features can be accessed from both a GlassFire program and a Ramp and Hold Program. Inspecting the glass while it is firing allows you to make certain adjustments on the very first firing however there are some precautions that should be observed.

The first is of course safety. Whether you are viewing your project by looking through the peephole or lifting the lid, be sure to observe all of the safety tips on page 5.

When lifting the lid to inspect the glass do not hold the lid open too long. The kiln will lose heat and take time to recover. It is important to note that when you release heat from the kiln during the process phase, the final temperature at which your piece is completed may change.

SKIP SEGMENT

The Skip Segment feature advances the program from the current segment to the next segment in the program. The Skip Segment feature can be used to stop the heatwork and advance the program to the annealing segments of the program. This feature should be used after a visual inspection of the glass indicates the effects you desire.

Skip Segment may also be used to speed up a GlassFire program when a slower firing rate is not required. This should

only be used with very small jewelry sized items.

To increase the heating portion of the program you can use Skip Segment to advance from the first segment of any program to the second segment. Since segment 2 in all GlassFire programs has a faster heating rate, it will reach the process temperature faster.

To decrease the amount of time spent during the Annealing segment of the program (segment 4) you may press anytime after the desired process has been achieved

Press while the kiln is firing. The display will first show the current segment and then display EdIt for approxi- mately 2 seconds. Press while EdIt is displayed in the screen. The display will then read SSEG for approximately 6 seconds. While it is displayed Press to advance the program.

You may now use the View Segment feature to verify the segment change.

ADD TIME

The Add Time feature adds time in 5 minute increments to the Hold Time in segment two. This is considered the Pro- cess Hold Time since it is holding at the peak temperature of the program. You will only be able to access this feature when the program is currently in the Segment 2 Hold. To verify the current segment use the View Segment Feature. It should display HLd2.

Press while the program is in Hold 2. The display will read the current segment then display EdIt for approximate- ly 6 seconds. Press while EdIt is displayed. The display will then show SSEG for 6 seconds. Press while SSEG is

displayed, to advance it to tME. Press to add 5 minutes to the Hold Time. The display will then return to showing the current temperature alternately with the changed Hold Time.

A D V A N C E D

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operating Manual Idle S Tate Glass Master Operating ManualRamp & Hold Programing PRO Mode Checking the Program A R T I N G Welcome to the World of Glass FusingBe Safe Wash the walls or lid of your kiln Set Up and LocationLocating the Kiln Programming Levels Beginner Beginner Plus MGF AdvancedIdle State Five Programming Modes Enter Stop Start Key Press DescriptionUP View Segment Down ReviewDisplay Messages CHGMGF StOP SsegTME TMPBasic Firing Steps LoadingAuto Mode Glassfire Visual Inspection UnloadingModifying Glassfire Programs Changing the Process Hold Time Start in Idle State Ramp & Hold Programing PRO ModeRate Checking the Program Only be used with very small jewelry sized items Edit Mode FeaturesOptions Mode Load ModeType of Glass What is a Firing Program?Heatwork Size and MassFiring Processes Critical Temperature RangesFusing By Lisa Vogt BasicsWhy does kiln wash stick to the back of a project? Frequently Asked QuestionsWhat causes sharp edges on the project? Stainless Steel Forms Err TroubleshootingErr F Err DHow Do I Get The Controller To Read Temperature In Celsius? How Do I Start Over And Reset Factory Settings?How Do I Make The Kiln Heat Faster In Glass Fire Mode? How Do I Make The Kiln Cool Faster?GlassFire Programs Factory Set Casting Program My Programs150F/hr 250F/hr 1000F/hr 30F/hr 0005 0230 0020Always Unplug the Kiln Prior to Doing ANY Repairs Warranty & RepairsElectrical Requirements Electrical Requirements & Wiring Diagram

Klin specifications

Skuttle Indoor Air Quality Products Klin is a prominent name in the field of indoor air quality solutions, dedicated to enhancing the health and comfort of indoor environments. With a focus on providing high-quality products that ensure clean and healthy air, Skuttle offers a range of technologies designed to meet diverse needs.

One of the primary features of Skuttle products is their advanced filtration systems. These systems utilize high-efficiency particulate air (HEPA) filters, which are capable of capturing 99.97% of airborne particles that are 0.3 microns in size. This quality ensures that allergens, dust, pollen, and pet dander are effectively removed from the indoor atmosphere, thereby substantially improving air quality.

In addition to filtration, Skuttle integrates humidification technology into its products. Humidifiers are essential for maintaining optimal humidity levels, which typically range from 30% to 50%. By adding moisture to the air, Skuttle humidifiers help alleviate respiratory issues, dry skin, and static electricity problems. The company’s digital humidistats offer precise humidity control, allowing users to monitor and adjust settings seamlessly.

Skuttle also places a strong emphasis on energy efficiency. Their products are designed not only to improve indoor air quality but also to reduce energy consumption. For instance, many Skuttle air quality solutions are equipped with innovative technologies that maximize airflow while minimizing resistance, leading to lower energy bills and a smaller environmental footprint.

The durability and reliability of Skuttle products are other notable characteristics. Constructed using high-quality materials, these units are built to withstand the rigors of daily use. Maintenance is made easy, as many products feature straightforward filter replacement processes and informative indicators to alert users when it’s time for upkeep.

User-friendly design is a hallmark of Skuttle Indoor Air Quality Products Klin. With intuitive controls and clear displays, customers can easily adjust settings to meet their specific requirements. This accessibility ensures that every household can enjoy the benefits of improved indoor air quality without complications.

In conclusion, Skuttle Indoor Air Quality Products Klin combines advanced technologies, energy efficiency, and user-friendly design to offer effective solutions for indoor air quality. With a commitment to enhancing health and comfort, Skuttle continues to be a leader in providing essential products that contribute to a cleaner and healthier living environment.
Top Page Image Contents