Skuttle Indoor Air Quality Products Klin manual Troubleshooting, Err F, Err D, Fail

Page 30

30

GENERAL INFORMATION

Troubleshooting

If you find yourself in this section of the manual please remember that Skutt and your Hot Start Kiln Dealer are here to help you as long as you own your kiln. If you are unable to determine the problem, or just need to order parts, please let us know.

KILN WILL NOT START

If there is no display, check to see if the kiln is plugged in and the breaker has not tripped. If there is a display, double check your programming instructions. The kiln must be in Idle Mode to start.

KILN WILL NOT REACH TEMPERATURE

Make sure the kiln is connected to the proper voltage. After extended use, the elements in the kiln wear out and eventu- ally need to be replaced. Look for possible breaks in an element. Elements can break if they are contaminated by bits of glass. If an element is out it will not glow. Fire the kiln to at least 500 °F and look in the kiln to see if an element is out.

KILN OVERFIRES OR UNDERFIRES

The thermocouple, which looks like a metal wire protruding into the kiln chamber, measures the temperature in the kiln chamber. As thermocouples began to wear out they slowly drift in the direction of an overfire. If you have noticed that your projects have become increasingly overfired it may be time to change your thermocouple. If you are comparing your results to how they fire in other kilns it is important to remember that every kiln fires slightly different and it may be necessary to adjust your firing programs.

Another possible cause would be that the factory programs have been changed. Look at the programs on page 25 and make sure they match the process temperature and process hold time that is entered in the program you are running. The last program run can easily be checked by pressing the Review key. To check other programs enter them while Modify GlassFire Mode is on. Remember, Process Hold times need to entered with Hours to the left of the decimal and Minutes to the right of the decimal.

G E N E R A L

ERROR MESSAGES

The following errors messages may appear in the display of your controller.

Err 1

Error 1 occurs during a firing segment programmed to increase the temperature. When the kiln is maintaining the programmed set point this error is not checked. If the kiln is unable to maintain the programmed set point the controller then requires that the kiln maintain a minimum rise of 12°F (4.8°C) per hour.

This usually indicates that the elements or the relay have failed. The kiln will shut off.

Err F

Error F occurs during a firing segment programmed to decrease the temperature. When the kiln is maintaining the programmed set point this error is not checked. If the kiln is unable to maintain the programmed set point the controller then requires that the kiln maintain a minimum fall of 12°F (4.8°C) per hour.

This usually indicates that a relay has failed and needs to be replaced. The kiln will shut off.

Err D

Error D occurs during a firing segment programmed to increase the temperature. If the kiln temperature is 100°F (38°C) or greater above the set point for 15 seconds then the controller registers an error d situation.

This usually indicates that a relay has failed and needs to be replaced. The kiln will shut off.

FAIL

This indicates that the thermocouple has failed and needs to be replaced. The kiln will shut off.

tc--

This indicates that the thermocouple has been installed backwards. The thermocouple needs to be removed and rein- stalled into the thermocouple block with the red wire inserted in the hole stamped “-”.

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operating Manual Glass Master Operating Manual Idle S TateRamp & Hold Programing PRO Mode Checking the Program Welcome to the World of Glass Fusing A R T I N GBe Safe Set Up and Location Wash the walls or lid of your kilnLocating the Kiln Programming Levels Beginner Beginner Plus MGF AdvancedIdle State Five Programming Modes UP View Segment Key Press DescriptionEnter Stop Start Down ReviewDisplay Messages CHGMGF TME SsegStOP TMPLoading Basic Firing StepsAuto Mode Glassfire Unloading Visual InspectionModifying Glassfire Programs Changing the Process Hold Time Ramp & Hold Programing PRO Mode Start in Idle StateRate Checking the Program Edit Mode Features Only be used with very small jewelry sized itemsLoad Mode Options ModeHeatwork What is a Firing Program?Type of Glass Size and MassCritical Temperature Ranges Firing ProcessesFusing Basics By Lisa VogtFrequently Asked Questions Why does kiln wash stick to the back of a project?What causes sharp edges on the project? Stainless Steel Forms Err F TroubleshootingErr Err DHow Do I Make The Kiln Heat Faster In Glass Fire Mode? How Do I Start Over And Reset Factory Settings?How Do I Get The Controller To Read Temperature In Celsius? How Do I Make The Kiln Cool Faster?GlassFire Programs 150F/hr 250F/hr 1000F/hr 30F/hr My ProgramsFactory Set Casting Program 0005 0230 0020Warranty & Repairs Always Unplug the Kiln Prior to Doing ANY RepairsElectrical Requirements & Wiring Diagram Electrical Requirements

Klin specifications

Skuttle Indoor Air Quality Products Klin is a prominent name in the field of indoor air quality solutions, dedicated to enhancing the health and comfort of indoor environments. With a focus on providing high-quality products that ensure clean and healthy air, Skuttle offers a range of technologies designed to meet diverse needs.

One of the primary features of Skuttle products is their advanced filtration systems. These systems utilize high-efficiency particulate air (HEPA) filters, which are capable of capturing 99.97% of airborne particles that are 0.3 microns in size. This quality ensures that allergens, dust, pollen, and pet dander are effectively removed from the indoor atmosphere, thereby substantially improving air quality.

In addition to filtration, Skuttle integrates humidification technology into its products. Humidifiers are essential for maintaining optimal humidity levels, which typically range from 30% to 50%. By adding moisture to the air, Skuttle humidifiers help alleviate respiratory issues, dry skin, and static electricity problems. The company’s digital humidistats offer precise humidity control, allowing users to monitor and adjust settings seamlessly.

Skuttle also places a strong emphasis on energy efficiency. Their products are designed not only to improve indoor air quality but also to reduce energy consumption. For instance, many Skuttle air quality solutions are equipped with innovative technologies that maximize airflow while minimizing resistance, leading to lower energy bills and a smaller environmental footprint.

The durability and reliability of Skuttle products are other notable characteristics. Constructed using high-quality materials, these units are built to withstand the rigors of daily use. Maintenance is made easy, as many products feature straightforward filter replacement processes and informative indicators to alert users when it’s time for upkeep.

User-friendly design is a hallmark of Skuttle Indoor Air Quality Products Klin. With intuitive controls and clear displays, customers can easily adjust settings to meet their specific requirements. This accessibility ensures that every household can enjoy the benefits of improved indoor air quality without complications.

In conclusion, Skuttle Indoor Air Quality Products Klin combines advanced technologies, energy efficiency, and user-friendly design to offer effective solutions for indoor air quality. With a commitment to enhancing health and comfort, Skuttle continues to be a leader in providing essential products that contribute to a cleaner and healthier living environment.
Top Page Image Contents